background image

 

GENERAL

2

 

NOTICE!

The source of the hazard is described here.

This combination of a symbol and a signal word indicates a potentially dangerous sit-
uation that may result in property or environmental damage unless avoided.

The actions to prevent the hazard are identified here

NOTICE!

This indicates a reference to another place in this text or another document.

This combination of a symbol and a signal word indicates a reference to another place
in this text or in a different document.

The places in the text or references to other documents are identified here.

TIPS AND RECOMMENDATIONS!

Simple tips and recommendations from our long years of experience are provided
here.

1.3

Copyright protection

The contents of this manual are protected by copyright. Their use is permitted within the scope of the use of
the installation. No further use is permitted without the written permission of the manufacturer. This manual
may not be copied, given to any third party, reproduced in any form or by any means, including, but not limited
to, exploitation and / or communication of the contents without the written permission of the manufacturer,
except for internal purposes.

1.4

Disclaimer

The information in this document has been compiled in consideration of applicable standards and regulations,
accepted rules of engineering, as well as our years of knowledge and experience.

The manufacturer shall not be liable for damages resulting from:

• Failure to observe the technical documentation
• Uses other than the intended use
• Use by personnel without the required training
• Unauthorized modifications or technical changes
• Use of non-approved spare parts or accessories

The actual scope of delivery may vary from the descriptions and images in this document in case of custom
versions, the selection of additional order options, or due to latest technical changes.

The obligations agreed in the supply contract, the general terms and conditions and the terms and conditions
of delivery, and the laws and regulations applicable at the time the contract was signed all apply.

We reserve the right to make technical changes to improve the usability and for further development.

Содержание U35





























Отзывы: