vacuubrand RC 6 Скачать руководство пользователя страница 43

Страница: 43 / 58

page 43 of 58

Fault

Possible cause

Remedy

❑

Oil leakage.

➨

Oil spilled?

✔

Absorb the oil and dis-

pose of according to reg-

ulations.

➨

Other cause?

✔

Contact local distributor.

❑

High oil consump-

tion.

➨

High inlet pressure?

✔

Normal. Top off oil when-

ever necessary. Install oil

mist filter at outlet.

➨

Operation with gas bal-

last?

✔

Top off oil whenever nec-

essary. Install oil mist filter

at outlet.

➨

Oil level too high?

✔

Lower oil level to mark

”max.”.

❑

Fast aging of the

oil.

➨

Pumping aggressive

gases?

✔

Use suitable oil.

➨

Condensation in the

pump?

✔

Use separator or cold

trap.

➨

Oil mist filter defective?

✔

Replace filter. Check

safety pop valve.

➨

Diaphragm pump does

not reach its pumping

speed?

✔

Perform maintenance of

diaphragm pump.

❑

Pump seized.

➨

Ambient temperature

too high ( > 104 °F

(40°C))?

✔

Provide sufficient ventila

tion.

➨

None of the above

mentioned causes?

✔

Contact local distributor.

Содержание RC 6



























































Результаты поиска

Содержание RC 6

Отзывы:

Похожие инструкции для RC 6

Бренды по названию

Популярные бренды

vacuubrand RC 6, Инструкция по эксплуатации

Результаты поиска

Содержание RC 6

Отзывы:

Похожие инструкции для RC 6

Бренды по названию

Популярные бренды