vacuubrand MD 4C NT + 2 AK Скачать руководство пользователя страница 45

Страница: 45 / 70

page 50 of 75

Fault

Possible cause

Remedy

Pump does not

start or stops im-

mediately.

Electrical power cord

not plugged in, electri-

cal supply failure?

Plug in power cord.

Check fuse.

Device fuse blown?

Identify cause of failure.

Replace device fuse.

Overpressure in outlet

line?

Remove blockage in line,

open valve.

Motor overloaded?

Allow motor to cool down,

identify and eliminate

cause of failure. Manual

reset is necessary. Switch

off pump or unplug.

Pump does not

achieve its ultimate

vacuum or usual

pumping speed.

Centring ring at small

correctly positioned, or

leak in the pipeline or

vacuum system?

Check pump directly -

connect vacuum gauge

directly at pump inlet -

then check connection,

pipeline and vacuum

system if necessary.

line?

Use lines with larger di-

ameter, length as short as

possible.

Pump has been ex-

posed to condensate?

Allow pump to run for

some minutes with atmo-

spheric pressure at the

inlet to purge.

Deposits have been

formed inside the

pump?

Clean and inspect the

pump heads.

Diaphragms or valves

damaged?

Replace diaphragms and/

or valves.

Outgassing substances

or vapor generated in

the process?

Check process parame-

ters.

Troubleshooting

Содержание MD 4C NT + 2 AK







































































Результаты поиска

Содержание MD 4C NT + 2 AK

Отзывы:

Бренды по названию

Популярные бренды

vacuubrand MD 4C NT + 2 AK, Инструкция по эксплуатации

Результаты поиска

Содержание MD 4C NT + 2 AK

Отзывы:

Бренды по названию

Популярные бренды