Vacon nxsp Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 31

background image

26 • vacon

lonworks interface

Tel: +358-201-2121 • Fax: +358-201-212 205

6

nciMinOutTime
This configuration property defines the minimum period of automatic network variable tansmission.

nciNmlSpeed
This configuration property is used to provide the nominal speed of the motor in RPM. This value is
necessary to determine the minimum and maximum speeds for the motor, based on the configuration
properties nciMinSpeed, nciMaxSpeed (entered as a percentage of nominal speed).

nciNmlFreq
This configuration property is used to provide the nominal frequency for the motor.

nciRampUpTm
Defines the acceleration time for Vacon NX. The valid range is 0.0 to 6,553.4 sec (0.1 sec).

nciRampDownTm
Defines the deceleration time for Vacon NX. The valid range is 0.0 to 6,553.4 sec (0.1 sec).

nciDrvSpeedScale
This configuration property is used as the default value for

nviDrvSpeedScale

. This value will be

adopted at power-up and in case no input variable within the specified Receive Heartbeat time is
received.

Archived Document

«
...
24
25
26
27
28
...
»

Содержание nxsp
































Отзывы:

Нет отзывов

Похожие инструкции для nxsp

Бренд: BADODOSECURITY Страницы: 8

Бренд: CAME Страницы: 18

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 28

Бренд: CAME Страницы: 4

Бренд: CAME Страницы: 40

Бренд: CAME Страницы: 26

Бренд: CAME Страницы: 34

Бренд: CAME Страницы: 2

Бренд: Danfoss Страницы: 85

VLT Decentral FCD 300

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 4

VLT 6000 series

Бренд: Danfoss Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 14

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды