V2 AYROS-24V series Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 30

background image

ENGLISH

- 48 -

12 - PROGRAMMING THE CONTROL UNIT

The configuration menu

-PrG

consists in a list of configurable

items; the display shows the selected item.
By pressing

i

, you will pass to the next item; by pressing

h

, you

will return to the previous item.

By pressing

OK

, you can view the current value of selected item

and possibly change it.

The last menu item (

FinE

) allows storing the carried out changes

and going back to the control unit normal operation.
You must exit from programming mode through this menu item if
you do not want to lose your configuration.

m

WARNING: in case no operation is carried out for more

than one minute, the control unit exits from the
programming mode without saving any of your setups and
changes, which will get lost.

By holding down the

i

or

h

keys, configuration menu items will

scroll fast, until item

FinE

is viewed.

In this way, you can quickly reach either the top or bottom of the
list.

EnSA

dir

FinE

-PrG

PARAMETER

VALUE

DESCRIPTION

DEFAULT

MEMO

dir

Gate direction (the direction you see from the inside)

dX

dX

The gate opens rightwards

SX

The gate opens leftwards

EnSA

Energy saving function

This function is useful for reducing the energy consumption of the
automation device while in stand-by mode.

If the function is enabled, the control unit will enter ENERGY
SAVING mode under the following conditions:
•  30 seconds after completion of an operational cycle
•  30 seconds after an opening (if automatic closure is not enabled)
•  30 seconds after exiting the programming menu

In ENERGY SAVING mode, power to the accessories, display,
flashing lights and closure electromagnets is deactivated.

ENERGY SAVING mode is exited:
• If an operational cycle is activated
• If one of the keys on the control unit are pressed

no

no

Function deactivated

Si

Function activated

P.APP

Partial opening

25

0 - 100

The percentage of the path the gate performs in the case of opening
using the Pedestrian Start command

t.PrE

Pre-blinking time

1.0”

0.5” - 1’00

Before any gate movement, blinker will be activated for

t.PrE

time, to

warn about the incoming motion (adjustable time from 0.5” to 1'00)

no

Function deactivated

t.PCh

Different closing pre-flashing time

no

0.5” - 1’00

If this parameter has a value assigned to it, the control unit will activate
pre-flashing prior to closure for the length of time set in this menu
(adjustable time from 0.5” to 1'00)

no

The closing pre-flashing time corresponds to

t .PrE

«
...
20
21
22
23
24
...
»

Содержание AYROS-24V series































Отзывы:

Нет отзывов

Похожие инструкции для AYROS-24V series

C-NaviGator III

Бренд: C-Nav Страницы: 20

Бренд: Jands Страницы: 7

Бренд: hager Страницы: 11

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Samson Страницы: 2

Бренд: ICP DAS USA Страницы: 166

Бренд: ICP DAS USA Страницы: 64

Tunnel Master Jr

Бренд: ICS Страницы: 83

PROFIBUS PROFI-2510

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 40

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 26

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA SIEMENS Страницы: 373

Бренд: York Страницы: 24

Бренд: Zeta Страницы: 44

Бренд: RKC INSTRUMENT Страницы: 10

Бренд: Haes Страницы: 42

Pearldex Series

Бренд: KaMo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды