![background image](http://html1.mh-extra.com/html/v2/axil/axil_manual_3097431013.webp)
E
N
G
LI
SH
11
IMPORTANT REMARKS
m
Prior to proceeding with installation, it is
essential the instructions be read in full, since they
contain important information regarding safety,
installation, use and maintenance.
AUTOMATION MUST BE IMPLEMENTED IN COMPLIANCE
WITH THE EUROPEAN REGULATIONS IN FORCE:
EN 60204-1, EN 12445, EN 12453, EN 13241-1,
EN 12635
• The installer must provide for a device
(es. magnetotermical switch) ensuring the omnipolar
sectioning of the equipment from the power supply.
The standards require a separation of the contacts of
at least 3 mm in each pole (EN 60335-1).
• The plastic case has an IP44 insulation; to connect
flexible or rigid pipes, use pipefittings having the
same insulation level.
• Installation requires mechanical and electrical skills,
therefore it shall be carried out by qualified personnel
only, who can issue the Compliance Certificate
concerning the whole installation (Machine Directive
2006/42/CEE, Annex IIA).
• Also the automation upstream electric system shall
comply with the laws and rules in force and be carried
out workmanlike.
• We recommend to make use of an emergency button,
to be installed by the automation (connected to the
control unit STOP input) so that the gate may be
immediately stopped in case of danger.
• For correct installation of the system, we recommend
following the instructions issued by UNAC very
carefully, which can be consulted at the following web
site: www.v2home.com
• This instruction manual is only for qualified
technicians, who specialize in installations and
automations.
• The contents of this instruction manual do not concern
the end user.
• Every programming and/or every maintenance service
should be done only by qualified technicians.
• Anything not expressly described in these instructions
is prohibited; unforeseen uses may be a source of
danger to people and property.
• Do not install the product in explosive environments
and atmospheres: the presence of inflammable gases
or fumes is a serious safety hazard.
• Do not make any modifications to any part of the
automation device, or the accessories connected to it,
unless described in this manual.
• Any other modifications will void the warranty on the
product.
• The installation steps should be conducted so as to
avoid rainy weather, which can expose electronic
circuits to dangerous water seepage.
• All operations requiring the casing of the device to
opened should be performed with the control unit
disconnected from the electricity supply and with a
warning notice displayed, for example: ”CAUTION,
MAINTENANCE IN PROGRESS”.
• Avoid exposing the device close to sources of heat and
flame.
• In the event of interventions on automatic or
differential breakers or fuses, it is essential that faults
be identified and resolved prior to resetting. In the case
of faults that cannot be resolved using the information
to be found in this manual, consult the V2 customer
assistance service.
• V2 declines all responsibility for failure to comply with
good construction practice standards in addition to
structural deformation of the gate that might occur
during use.
• V2 reserves the right to make modifications to the
product without prior warning.
• Installation/maintenance personnel should wear
individual protection devices (IPDs), such as overalls,
safety helmets, boots and gloves.
• The ambient operating temperature should be that
indicated in the technical characteristics table.
• The automation device should be shut down
immediately in the event of any anomalous or
hazardous situation; the fault or malfunction
should be immediately reported to the person
responsible.
• All safety and hazard warnings on the machinery and
equipment should be complied with.
• Electromechanical actuators for gates are not intended
to be used by people (including children) with
diminished physical, sensory or mental capacity, or
lacking in experience or knowledge, unless they are
under supervision or have been instructed in use of the
actuator by a person responsible for safety.
V2 has the right to modify the product without
previous notice; it also declines any responsibility to
damage or injury to people or things caused by
improper use or wrong installation.
DISPOSAL OF THE PRODUCT
As for the installation operations, even at the end of this
product’s life span, the dismantling operations must be
carried out by qualified experts.
This product is made up of various types of materials:
some can be recycled while others need to be disposed
of. Find out about the recycling or disposal systems
envisaged by your local regulations for this product
category.
Important!
– Parts of the product could contain pollutants
or hazardous substances which, if released into the
environment, could cause harmful effects to the
environment itself as well as to human health.
As indicated by the symbol opposite, throwing away this
product as domestic waste is strictly forbidden. So
dispose of it as differentiated waste, in accordance with
your local regulations, or return the product to the
retailer when you purchase a new equivalent product.
Important!
– the local applicable regulations may
envisage heavy sanctions in the event of illegal disposal
of this product.