manualshive.com logo in svg
background image

Installation instructions

Heat pump dryer
Multi-family building

J173.113-0

6.4.11  ITH

3

1. Remove the transport packaging.

2. Raise the appliance on one side and pull out one half of the installation plate.

3. Raise the appliance on the other side and pull out the other half of the installation plate.

4. Fit the two halves of the installation plate together and place in the desired position (observe 

minimum distances, see table). If there are plumbing fittings behind the appliance or if the 
surrounding walls are not perpendicular, these distances must be adjusted accordingly.

5. Affix the installation plate to the floor using the double-sided adhesive tape supplied. The 

installation plate can also be screwed to the floor.

Washer-dryer tower

Minimum distances

Installation

Work steps 

1

5

 must be carried out in full in the order specified.

1. Positioning the installation plate

Use the installation plate to install the appliance. This plate fixes the appliance in position.

The minimum distances to walls and distances to adjacent appliances must be observed (see table).

Use the floor attachment set (article no. 81.1311.32) for an uneven or sloping floor. 
In such instances, the installation plate cannot be used.

The heat pump dryer can only be combined with a washer-dryer tower if the 

minimum room height

 

and 

side access

 for cleaning are ensured.

Installation is not possible in a closed niche!

1. Raise the dryer on one side and pull out one half of the installation plate.

2. Raise the dryer on the other side and pull out the other half of the 

installation plate.

3. Fit the two halves of the installation plate together and affix the 

installation plate to the clean and dry cover plate using the double-sided 
adhesive tape supplied. Press down firmly (see picture for alignment).

If you want to screw down the installation plate, use screws no 
longer than 12 mm.

Minimum distance

A

B

C

Single appliance

10 mm

250 mm

Washer-dryer tower

600 mm

250 mm

Appliances positioned side by side

10 mm

250 mm

10 mm

min. 1950 mm

Room height

65,5

B

A

B

A

C

Washing

machine

Tumble

dryer

Содержание 173







Отзывы: