Uvitron Intelliray 600 Скачать руководство пользователя | Manualshive

Страница: 29 / 36

background image

Uvitron International INTELLI-RAY 600 Instruction Manual, Rev. T

Page 29 of 36

TROUBLESHOOTING (CONTINUED)

9

9.2 System Alarms

The  IntelliRay  control  system  has  the  ability  to  monitor  the  lamp’s  subsystems  for  abnormal
conditions, and to warn the operator by triggering an alarm. In such a case, an audible warning
beep  will  sound  and  an  appropriate  pop-up  message  will  be  displayed  on  the  system  LCD
display.  All  active  alarms  will  be  subsequently  displayed  in  an  Alarm  Log  which  will  appear  at
the bottom of the main menu. Refer to the chart below for the sequence of alarm menu items:

Oven Over-Temp

ENTR = Acknwldge

ENTR

Setup = ENTR,

Cure Menu = MENU

MENU

ALARM PRESENT

ENTR to View

ENTR

Alarm Pop-Up will be
displayed when a system
alarm condition is detected:

Once the alarm message
has been viewed and
acknowledged, the display
will return to the top of the
main menu:

Oven Over-Temp

MENU to Continue

ALARM LOG

ENTR to View

ENTR

After alarm acknowledged, a
new Alarm Log item appears
at the bottom of Main Menu:

“Clear All” will remove all
alarms from log, turn off
the Alarm LED, and
prevent the active alarms
from being reported again
until main power is cycled.

ENTR = Clear All

MENU = Continue

ENTR

Are you sure?

ENTR = CONFIRM

MENU

MENU

ENTR = Main Menu

MENU = Alarms

ENTR

Setup = ENTR,

Cure Menu = MENU

MENU

MENU

MENU

List all active alarm(s)

MENU

ENTR

Alarm Pop-up

Alarm Log

«
...
27
28
29
30
31
...
»

Содержание Intelliray 600





































Отзывы:

Нет отзывов

Похожие инструкции для Intelliray 600

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: Oberheim Страницы: 40

Бренд: Pari Страницы: 50

Бренд: Icare Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды