UTICA BOILERS UB90 125 Скачать руководство пользователя

Страница: 7 / 44

OVERHANG

12" MINIMUM

90°

VENT

12" SEPARATION
BETWEEN BOTTOM OF
COMBUSTION AIR INTAKE

AND BOTTOM OF VENT

MAINTAIN 12" MINIMUM
CLEARANCE ABOVE HIGHEST

ANTICIPATED SNOW LEVEL OR
GRADE

MAXIMUM

SEPARATION

18"

MAXIMUM

15"

MAXIMUM

LESS THAN 12" CLEARANCE

12"

MINIMUM

12"

MINIMUM

12" OR MORE CLEARANCE

90°

BRACKET

VENT

18"

MAXIMUM

MAINTAIN 12" MINIMUM
CLEARANCE ABOVE HIGHEST

ANTICIPATED SNOW LEVEL OR

GRADE

12" SEPARATION
BETWEEN BOTTOM OF
COMBUSTION AIR INTAKE

AND BOTTOM OF VENT

12" MINIMUM

OVERHANG

MAXIMUM

SEPARATION

12"

MINIMUM

12"

MINIMUM

Advise owner of boiler to keep venting and combustion

air intake passages free of obstructions. Both venting

and combustion air intake piping systems connected

to outdoors must permit fl ow through piping systems

without restrictions for boiler to operate.
Boiler shall be installed such that automatic gas

ignition system components are protected from water

(dripping, spraying, rain, etc.) during operation and

service (circulator replacement, condensate trap,

control replacement, etc.).
Boiler must be located where ambient temperatures

(minimum possible room temperatures where boiler

is installed assuming boiler is not in operation and

therefore contributes no heat to space) are always

at or above 32°F (0°C) to prevent freezing of liquid

condensate.

Combustion Air/Vent Pipe Requirements
Boiler requires dedicated direct vent system. In direct vent

system, all air for combustion is taken directly from outside

atmosphere, and all fl ue products are discharged to outside

atmosphere.
Combustion air and vent pipe connections must terminate

together in same atmospheric pressure zone, either

through roof or sidewall (roof termination preferred). See
Figures #1 and #2 for required clearances.

If concentric vent termination is being used, refer to

Figure #3 for proper setup.

Less Than 12” Clearance

12” or More Clearance

BEFORE INSTALLING THE BOILER

Figure 1 - Roof Vent / Intake Terminations

Figure 2 - Sidewall Vent/Intake Terminations

Figure 3 - Concentric Vent Terminations

Содержание UB90 125













































Результаты поиска

Содержание UB90 125

Отзывы:

Похожие инструкции для UB90 125

Бренды по названию

Популярные бренды

UTICA BOILERS UB90 125, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UB90 125

Отзывы:

Похожие инструкции для UB90 125

Бренды по названию

Популярные бренды