manualshive.com logo in svg

UTICA BOILERS UB90 125, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
UTICA BOILERS UB90 125 Скачать руководство пользователя страница 31

31

DRAFT INDUCER TEMPERATURE SAFETY SWITCH

if draft  inducer temperature reaches temperature safety switch 
set-point, safety switch contacts open immediately, closing gas 
valve 

(light goes out)

.

Draft  inducer runs through 30 second post purge and switches 
OFF.

Circulator runs with thermostat on call for heat.

When temperature safety switch contacts remake before end of 
call for heat, control goes into normal light-off  sequence.

LOSS OF COMBUSTION AIRFLOW

If combustion airfl ow is lost while burner is fi ring (Diff erential 
air pressure switch contacts open) gas valve will be de-
energized. 

Valve and fl ame lights go out.

Draft  inducer runs through 30 second post purge.

If call for heat remains, IBC waits 5 minutes for airfl ow to be 
re-established.

If airfl ow does not re-establish control lockout - problem with 
combustion airfl ow. 

Purge light blinks

. Control will 

automatically reset aft er 15 minutes.

LOSS OF FLAME SIGNAL

if an established fl ame signal is lost while control expects that 
the burner is operating, control will immediately de-energize 
gas valve. 

Valve and fl ame lights go out.

Draft  inducer runs through 30 second post purge.

Control will attempt to relight boiler 3 times. if fl ame is not 
proven, control lockout - problem establishing a fl ame signal. 

Valve light is blinking

. Control will automatically reset 

aft er 1 hour.

HIGH LIMIT CONTROL

if boiler water temperature reaches high limit (aquastat) 
setpoint, high limit n.c. contacts open immediately, closing gas 
valve. 

Valve and fl ame lights go out.

Draft  inducer continues to run for 30 second post purge and 
switch OFF.

Circulator runs as long as thermostat calls for heat.

When high limit contacts remake before end of call for heat - 
control goes into a normal light-off  sequence.

CASTING TEMPERATURE SAFETY SWITCH

If burner operates when boiler has no water, aluminum boiler 
sections heat up rapidly.

Casting temperature safety switch contacts will open, breaking 
24 volt power to ibc. power indicator light goes out. Requires 
manual reset to re-close contacts.

 Power light goes out.

CIRCULATOR PUMP

Circulator will be energized as long as thermostat calls for heat 
during lockout.

Recovery from any lockout requires reset, which can be 
accomplished by:

(a) Removing and reestablishing the thermostat’s call for heat 
or turning the service switch off  and back on; 
                                             or 
(b) Waiting for the control to automatically reset aft er 15 
minutes for loss of combustion airfl ow or one hour for loss of 
fl ame.

DETAILED SEQUENCE OF OPERATION

Содержание UB90 125













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды