UTICA BOILERS MGB-100J Скачать руководство пользователя

Страница: 23 / 28

APPENDIX A - CONTROL MODULE

A.1 Installation Environment Considerations

WARNING

If you do not follow these instructions

exactly, a fi re or explosion may result

causing property damage, personal injury

or loss of life.

• Do not use this appliance if any part has

been under water.

Immediately call a quali

service technician to inspect appliance and to

replace any part of control system and any gas

control which has been under water.

• Do not allow water to drip on controls. Prevent

condensation by allowing air circulation around

module and gas control.

• Do not use corrosive chemicals around or on

module or gas control.

• Controls can be damaged by excessively high

temperatures. Verify adequate air circulation around

control is maintained when installing boiler.

A.2 Electrical Connections
Connect Module Connectors Figure 13, Page 16

• Connect L1& L2 leads inside J-box using wire nuts.

Secure J-box cover.

• Connect Circulator harness to circulator. Harness

comes plugged into module with Molex

plug.

• Connect thermostat connection to yellow wires

marked TT using wire nuts.

• Ensure remaining Molex

plug connectors have not

worked loose during transit.

• Check sensing bulb is fully inserted in well and is not

loose.

A.3 Adjusting Settings

To discourage unauthorized changing of settings, procedure

to enter adjustment mode is required.
To enter adjustment mode, press UP, DOWN, and I buttons

simultaneously for three seconds. Press and release I

button until parameter requiring adjustment is displayed.
See Figure 12, page 16.

“SP_” Setpoint (180 °F default setting; adjustable

between 130 and 220 °F)

“Df_” Setpoint Differential (15 °F default setting;

adjustable between 10 and 30 °F)

“°F_” Degrees

Fahrenheit

Press UP or DOWN button until parameter has reached

desired value. After 60 seconds without any button inputs,
control automatically returns to READ mode.

A.4 Display

In RUN mode, status items and parameters are viewable.

Example

, to display setpoint, control

ashs “sp” (setpoint)

followed by temperature (i.e., 135), followed by °F or °C.
To read settings, press and release I key to

nd parameter

of interest.

Example,

press and release I until setpoint (sp) is

displayed, followed by three-digit number, i.e., 190,

followed by °F or °C. Press I button again will display (S1T)

Sensor 1 Temperature followed by three-digit number and

corresponding degree designator.
See Display Readout.

Figure 22 - Display Readout

Содержание MGB-100J





























Результаты поиска

Содержание MGB-100J

Отзывы:

Похожие инструкции для MGB-100J

Бренды по названию

Популярные бренды

UTICA BOILERS MGB-100J, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MGB-100J

Отзывы:

Похожие инструкции для MGB-100J

Бренды по названию

Популярные бренды