background image

14

8 - CONNECTING GAS SERVICE

General

• Use piping materials and joining methods acceptable 

to authority having jurisdiction.  In absence of such 

requirements National Fuel gas Code, ANSI Z223.1/

NFPA 54

• Size and install gas piping system to provide suf

fi

 cient 

gas supply to meet maximum input at not less than 

minimum supply pressure. See Table 4.

• Support piping with hooks straps, bands, brackets, 

hangers, or building structure components to prevent or 

dampen excessive vibrations and prevent strain on gas 

connection.  Boiler will not support piping weight.

• Use thread (joint) compound (pipe dope) suitable for 

lique

fi

 ed petroleum gas.

• Install 

fi

 eld sourced manual main shutoff valve, ground 

joint union, and sediment trap upstream of gas valve. 

See Figure 12.

Table 5

Natural Gas

Propane

Min. Supply Pressure

5" w.c.

11" w.c.

Max. Supply Pressure

13.5" w.c.

13.5" w.c.

Manifold Pressure

3.5" w.c.

10.5" w.c.

DANGER

Fire Hazard.  Do not use matches, candles, open 

fl

 ames, or other methods providing ignition source. 

Failure to comply will result in death or serious 

injury.

!

  

Leak Check Gas Piping

Pressure test boiler and gas connection before placing 

boiler in operation.

• Pressure test over 1/2 psig (3.5 kPa).  Disconnect 

boiler and its individual gas shutoff valve from gas 

supply system.

• Pressure test at 1/2 psig (3.5 kPa) or less.  Isolate 

boiler from gas supply system by closing manual gas 

shutoff valve. 

• Locate leakage using gas detector, noncorrosive 

detection 

fl

 uid, or other leak detection method 

acceptable to authority having jurisdiction.  Do not 

use matches, candles, open 

fl

 ames, or other methods 

providing ignition source.

• Correct leaks immediately and retest.

MAXIMUM CAPACITY OF PIPE IN CUBIC FEET OF 

GAS/HOUR

(Gas Pressure = 0.5 psig or less, Pressure Drop = 5 

in. w/c)

Table 4

Length of 

Pipe (Feet)

Nominal Iron Pipe Size

½”

¾”

1”

1¼”

10

175

360

680

1400

20

120

250

465

950

30

97

200

375

770

40

82

170

320

660

60

66

138

260

530

80

57

118

220

460

100

50

103

195

400

For additional information refer to the National Fuel Gas 

Code Handbook.

Figure 12 - Gas Piping

CAUTION

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use 

any phone in your building.

• Immediately call your gas supplier from a 

neighbor’s phone.  Follow gas supplier’s 

instructions. 

• If you cannot reach your gas supplier, call the 

fi

 re 

department.

!

!

  

Содержание MGB-100J





























Отзывы: