background image

 

 

 

 

Operating Your Laminator… 

 
Your new laminator arrives ready-to-run.  Load the laminating film and install the feed table 
and heat guard as detailed in the section titled “Loading Film.”  Plug the laminator into an 
appropriate power supply and set the Heat Switch to the “ON” position.   Next, set the 
temperature according to the film manufacturer’s recommendations for the film you have 
chosen, and allow the machine to heat for approximately 30 minutes.  Temperature adjustment 
is detailed in the section titled “Heat Settings.” 
 
After 30 minutes of heating time, set the Motor Drive Switch to the “FORWARD” position and 
allow the rubber rollers to rotate ½ turn.  Set the Motor Drive Switch to the “OFF” position and 
allow the machine to heat an additional 30 minutes before use.  Check the heat setting and 
adjust as necessary. 
 
Set the Motor Drive Switch to the “FORWARD” position and perform a test lamination to 
ensure proper settings for successful lamination.  Watch film as it exits the rollers so it doesn’t 
wrap around the rollers.  It may be helpful to hold the exiting film at first when starting a 
lamination run.  If any adjustments are necessary make them now and run another test; see 
adjustment details in the section titled “Tension.”  Repeat this step until you obtain desired 
results. 
 
When laminating, run a small amount of film before feeding the print into the laminator to 
avoid a “dwell line” across the leading edge of your print.  Feed the print slowly and evenly.  
Smoothing the print or keeping “back pressure” on it as the rollers pull it through will help to 
ensure a professional, wrinkle free finish.  You may laminate subsequent prints now, leaving 
appropriate space between each print for trimming. 
 
When your last print has cleared the pull rollers and completely exited the laminator, set the 
Motor Drive Switch to the “OFF” position.  Do Not use the Speed Control Knob to turn the drive 
system off; the speed control is only to be used for controlling speed. 
 
When you have finished laminating, set the Heat Switch and the Motor Drive Switch to the 
“OFF” position and unplug the machine at the end of the day. 

 

Loading Film… 

 
For non-Color-Coded laminators: 
 
Select the two rolls of laminating film that you wish to use.  Both rolls of film should be of the 
same size, type and thickness.  Note:  Always operate the laminator with two rolls of laminating 
film of the same width to avoid excessive adhesive transfer to the Rubber Rollers.  Next, take 
the Bottom Supply Mandrel (labeled “Low”) and insert it into the roll of film until the “gripper 

Содержание ARL 4000















Отзывы: