manualshive.com logo in svg

US Water Systems Aquapurion 200-APRO Series, Руководство пользователя

Поделиться
Скачать
US Water Systems Aquapurion 200-APRO Series Скачать руководство пользователя страница 5

Installation Instructions 

Residential Reverse Osmosis Drinking Water System 

Page 5 

 

NOTE: All plumbing must be completed in accordance 
with  state  and  local  plumbing  codes.  Some 
municipalities  may  require  the  installation  be 
performed by a licensed plumber. Check your local 
authority prior to installation. 

A. Faucet installation 

If  the  sink  has  a  sprayer  it  may  be  disconnected  for 
faucet  installation.    A  pipe  cap  or  plug  will  be 
necessary  to  seal  the  sprayer  connection.    To  make 
the faucet mounting hole (if sprayer or second hole is not 
used),  check  below  to  make  sure  the  drill  does  not 
interfere with anything below. Drill a 7/8” minimum 1 1/8” 
maximum hole for air gap faucet installations and a 7/16’ 
hole  for  non-air  gap  faucets.  Be  sure  to  use  a  bit 
compatible  with  your  surface.    Clean  up  sharp  edges.  
The  faucet  should  be  positioned  so  it  empties  into 
the  sink  and  the  spout  swivels  freely  for 
convenience.  If  sink  has  a  hole  that  can 
accommodate the RO faucet, no drilling is required.  
Proceed with mounting the faucet. 

 

FEED WATER CONNECTION 

is accomplished with an angle stop feed water valve. This valve will be installed in 

the cold water line between the sink cold water shutoff valve and the sink faucet tubing. Connect to a potable, cold wa-
ter supply line only. 

NOTE: 

Softened water is preferred since it will extend the life of your R/O membrane.

 

DRAIN CONNECTION 

is accomplished using a waste water saddle valve which is designed to fit around a standard 

1-1/2” OD drain pipe. The drain saddle valve should always be installed above (before) the trap and on the vertical or 
horizontal tailpiece. 

Do not install the drain saddle valve near a garbage disposal; otherwise, plugging of the waste water line may occur. If dis-
charging into a utility sink or standpipe, an air gap may be needed. (Air gaps must be 1” or greater above the floor or pipe 
rim).  US Water offers other drain line connection options on www.uswatersystems.com 

NOTE: 

Plumbing codes may require the use air gaps. Please check with your local municipality.

 

Do not connect the R/O system drain line to the dishwasher drain line due to the fact back pressures may cause the air 
gap to overflow. 

RO System Installation Procedure 

Fig. 1 

Содержание Aquapurion 200-APRO Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды