manualshive.com logo in svg

US Shift 4R70W, Инструкция по установке и эксплуатации, Страница: 34 / 36

Поделиться
Скачать
US Shift 4R70W Скачать руководство пользователя страница 34

34

 

OSS Circuit Open or Sensor Missing 

The Output Shaft Speed Sensor circuit is open or the sensor is missing. 
 

ISS Circuit Open or Sensor Missing 

The Input Shaft (Turbine) Speed Sensor circuit is open or the sensor is missing. 
(if equipped) 
 

OSS Sensor Signal Plausibility Error 

The controller detected an unexpected value from this sensor and marked it as 
faulty. 

 
ISS Sensor Signal Plausibility Error 

The controller detected an unexpected value from this sensor and marked it as 
faulty. (if equipped) 

 

Checksum error in table

 

A Checksum error has been found in the calibration table. It will also disable 
saving Setup Menu changes and disable the tuning menu. Connect the 
controller to a PC and load a calibration using Shiftware. 
 

Torque Converter Clutch Slip Error 

Torque converter clutch slip detected when fully engaged. 
 

Transmission Slip in Gear(s) 1, 2, 3, etc. 

Transmission appears to be slipping in the indicated gear or gears. 
 

Transmission Slip with Max Pressure 

Transmission continued to slip after maximum line pressure was commanded. 
 

Transmission Slip Repeated > 2x 

Transmission slip was detected more than twice in this drive cycle (max. line 
pressure latched). 
 

Ratio too High in Gear(s) 2, 3, 4, etc. 

Transmission gear ratio appears to be too high in the indicated gear or gears. 
 

Error: PRNDL Out of Range 

Sensor voltage is out of tolerance limits, but within approximate range. 
 

Содержание 4R70W





































Отзывы:

Нет отзывов