US Shift 4R70W Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 36

US Shift 4R70W Скачать руководство пользователя страница 33

33

EPC (PCS) Solenoid circuit shorted

Line Pressure Control Solenoid

resistance measured too low during the power-

on solenoid check. Refer to the data display screen in the diagnostic menu to
see the measured solenoid resistance.

Shift Solenoid A (SSA) circuit open

The indicated Shift Solenoid’s resistance measured too high during the power-
on solenoid check. Refer to the data display screen in the diagnostic menu to
see the measured solenoid resistance.

Shift Solenoid B (SSB) circuit open

The indicated Shift Solenoid’s resistance measured too high during the power-
on solenoid check. Refer to the data display screen in the diagnostic menu to
see the measured solenoid resistance.

TCC Solenoid circuit open

TCC pressure solenoid resistance measured too high during the power-on
solenoid check. The controller will attempt to disable the TCC solenoid until the
ignition is turned off. Refer to the data display screen in the diagnostic menu to
see the measured solenoid resistance.

EPC (PCS) Solenoid circuit open

Line Pressure Control Solenoid

resistance measured too high during the power-

on solenoid check. Refer to the data display screen in the diagnostic menu to
see the measured solenoid resistance.

TPS Voltage Low; run TPS Setup

The Throttle Position Sensor is in fault mode due to the voltage being below the
idle threshold value that was set. Run TPS calibration in the setup menu.

TFT Circuit Voltage Low or Shorted

The Transmission Fluid Temperature sensor voltage is too low. A possible cause
of this could be that it is shorted to ground.

TFT Circuit Voltage High or Open

The Transmission Fluid Temperature sensor voltage is too high. The TFT sensor
circuit could be open.

Transmission is Overheating

The temperature in the transmission is above the allowed threshold.

«
...
31
32
33
34
35
...
»

Содержание 4R70W





































Отзывы:

Нет отзывов