US Shift 4R70W Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 36

US Shift 4R70W Скачать руководство пользователя страница 27

27

SHIFTWARE

Introduction

Using the Shiftware software allows you to modify the way your Quick 2
Transmission Control System behaves. You can customize shift-points as well
as monitor and diagnose the Quick 2 unit in real-time.

Setup

To create a calibration for the Quick 2, it is best to start with one of the standard
calibrations which are included with the software. To load a standard
configuration for your transmission, click the

Open

button on the toolbar,

then browse to the folder where the transmission calibration files are located.
(Default location is C:\Shiftware\) The files are named according to the
transmission and RPM range and have the .btc file extension. Choose the
calibration file and click

Open

.

Once the calibration file is loaded, click the

System Settings

button on the

toolbar to check the settings and make sure that they are correct for your
transmission. The System Settings window has several tabs within it. Click each
one to see each section of settings specific for your transmission.

The System Settings Window

«
...
25
26
27
28
29
...
»

Содержание 4R70W





































Отзывы:

Нет отзывов