manualshive.com logo in svg

US Robotics Courier V.34, Руководство пользователя


Поделиться
Скачать
background image

COURIER HIGH SPEED MODEMS

A-8    Link Negotiation and Error Control

Xmodem

Throughput may be reduced if your version
uses short block lengths (128 bytes).  Some
versions use larger blocks (1K blocks).
Throughput is also reduced by overhead
(error control protocol information).

Ymodem

There is an improvement over Xmodem, due
to larger block lengths (1K bytes), but
throughput is still reduced by the protocol's
error control overhead.

The above protocols further reduce throughput when an
error control connection is established.  The accuracy of the
data is checked both by the file transfer protocol and the
modem.  To avoid redundancy, use the above protocols
only for non-ARQ connections, and only at speeds of 2400
bps and below.

For the best throughput, but on error-controlled connections
only and with hardware flow control, we recommend the
most current version of Zmodem.  Overhead is minimal
with this protocol, with throughput almost equal to that
obtained with no file-transfer protocol.  Zmodem should
also be used for non-ARQ connections.  Leave the modem
at its &M4 and &K1 settings for both error control and data
compression.  Ymodem-G is another good choice, but never
without both the local and remote modems using error
control:  if Ymodem-G detects an error, it aborts the
transfer.  Do not use either protocol with software flow
control (XON/XOFF signaling).

Typical Throughput

The maximum connection rate between two V.34 modems is
28.8K bps.  Ocassionally, connections occur at 26.4K, 24K, and
21.6K bps because line quality differs from location to location
Line conditions and data rate affect throughput.  Also
remember, your serial port rate must match or exceed your
connection rate.  If you set your serial port rate at 19.2K bps, the
V.34 modem will only connect at or below 19.2K bps.

Содержание Courier V.34






















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Courier V.34

SCS PTC-IIIusb User Manual preview
PTC-IIIusb
Бренд: SCS Страницы: 217
TP-Link VX420-G2v Setup Manual preview
VX420-G2v
Бренд: TP-Link Страницы: 4
Best Data Products DSL542EU User Manual preview
DSL542EU
Бренд: Best Data Products Страницы: 41
Magellan U-Link TRx User Manual preview
U-Link TRx
Бренд: Magellan Страницы: 10
Sixnet VT-MODEM User Manual preview
VT-MODEM
Бренд: Sixnet Страницы: 30
NXP Semiconductors TDA5051A Product Data Sheet preview
TDA5051A
Бренд: NXP Semiconductors Страницы: 29
tecnoelettra TE809 Instruction Manual preview
TE809
Бренд: tecnoelettra Страницы: 8
3Com 3C871 Quick Start Instructions preview
3C871
Бренд: 3Com Страницы: 15
Flightcell MOP 00010 Installation Manual preview
MOP 00010
Бренд: Flightcell Страницы: 12
SMC Networks SMCD3GN-RRR User Manual preview
SMCD3GN-RRR
Бренд: SMC Networks Страницы: 100
US Robotics 005690-00 Installation Manual preview
005690-00
Бренд: US Robotics Страницы: 2
RACOM PROFI MR300 Operating Manual preview
PROFI MR300
Бренд: RACOM Страницы: 17
Feeney Wireless Skyus 3G Sprint Quick Start Manual preview
Skyus 3G Sprint
Бренд: Feeney Wireless Страницы: 11
ProComSol HART HM-BT-BAT User Manual preview
HART HM-BT-BAT
Бренд: ProComSol Страницы: 6
Jinan USR IOT Technology USR-GPRS-MODEM User Manual preview
USR-GPRS-MODEM
Бренд: Jinan USR IOT Technology Страницы: 12
Canon w-e1 Instruction Manual preview
w-e1
Бренд: Canon Страницы: 98
Paradyne StormPort 1020 Installation And User Manual preview
StormPort 1020
Бренд: Paradyne Страницы: 2
DCB V.23 Quick Start Manual preview
V.23
Бренд: DCB Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды