Urrea GGI810, Руководство пользователя и гарантия

Страница: 22 / 30

20
AC APPLICATIONS
Before connecting an appliance or the power
cable to the generator:
Make sure it is in good working order. Defec-
tive devices or power cords can create an electric
shock potential.
If an appliance starts functioning abnormally,
becomes slow or stops suddenly, turn it off im-
mediately. Disconnect the appliance, and deter-
mine if the problem is the appliance, or if the
nominal capacity of the generator has been ex-
ceeded.
Make sure that the electrical rating of the tool
or device does not exceed that of the generator.
Never exceed the maximum power of the gen-
erator. Power levels between nominal and maxi-
mum can be used for no more than 30 minutes.
AC OPERATION
1. Start the engine and make sure that the
output light (green) lights up.
2. Plug in the appliance. Most motorized
devices require more than their nominal
power for the start. If the generator is
overloaded or if a short circuit occurs in a
connected device, the overload indicator
light (red) will light. The overload indicator
light (red) will remain on, and after about
four seconds, the power to the connected
device will turn off, and the output light
(green) will turn off. Stop the engine and
investigate the problem.
DC OPERATION
The DC receptacle should ONLY be used to
charge 12 volt automotive type batteries. The
DC load output is not regulated.
When the DC output is used, set the Eco-acceler-
ator switch to the OFF position. Connecting the
battery charging cable (optional equipment):
1. Before connecting the battery charging
cable to a battery that is installed in a ve-
hicle, disconnect the ground wire of the
vehicle battery from the negative (-) of the
battery.
WARNING: The battery emits explosive gases;
Keep sparks, flames and cigarettes away. Pro-
vide adequate ventilation when charging or us-
ing batteries.
WARNING: The terminals, terminals and related
accessories contain lead and lead components.
Wash your hands after handling.
2. Connect the battery charging cable to the
DC receptacle of the generator.
3. Connect the red cable from the battery
charging cable to the positive (+) terminal
of the battery and the black cable to the
negative (-) terminal of the battery.
4. Start the generator.
Disconnect the charging cable from the battery:
1. Stop the engine.
2. Disconnect the black cable from the bat-
tery charging cable from the negative (-)
terminal of the battery.
3. Disconnect the red wire from the battery
charging cable from the positive terminal
(+) of the battery.
4. Disconnect the battery charging cable
from the generator’s DC outlet.
5. Connect the ground wire of the vehicle
battery to the negative (-) terminal of the
battery.
ECONOMIC MODE
If high electrical loads are connected simultane-
ously, turn the Eco-accelerator switch to the off
position to reduce the voltage changes.
The economic system is not effective for use
with appliances that require momentary power.
If you use these devices, deactivate this mode
(OFF).
PRE-OPERATION CHECK
ENGINE OIL
Check the oil level before each use with the gen-
erator on a horizontal surface and the engine
stopped. Use 4-stroke engine oil that meets or
exceeds the requirements for API SJ classifica-
tion service or later (or equivalent). Always
check the API service label of the oil container
to make sure it includes the letters SJ or later
(or equivalent).
SAE 10W-30 oil is recommended for general use
at any temperature. Other viscosities shown in
the graph can be used when the average tem-
perature of your generator is within the indi-
cated range
1. Place the generator on a level surface.
2. Loosen the screw on the cover and remove
the maintenance cover.
3. Remove the oil filler cap and clean the dip-
stick.
4. Check the oil level by inserting the rod into
the filler neck without screwing it.
5. If the level is low, fill up to the upper
limit of the oil filler neck with the recom-
mended oil.
6. Reinstall the maintenance cover and
tighten the cover screw firmly.
FILLING OF FUEL
With the engine stopped, remove the fuel tank
cap and check the fuel level. Refill the fuel tank
if the fuel level is low. Fill the tank with care to
avoid spilling fuel. Do not fill.