sec.4b
−−−−
5
2 VOICE - Technical Manual
DOOR PHONE APARTMENT STATIONS
DOOR OPEN LED
The function is only active for the last called door phone on which
the door opening button was pressed and corresponding to the last
calling door unit; see the “LED indications” for more details.
Open door function is available only if a suitable sensor has
been connected to the door unit.
OPTIONALPROGRAMMING
The following programming operations are needed after testing the
basic operation of the system, only if are required.
INTERCOM FUNCTION
Buttons ( , , ) can be programmed in 2Voice systems for intercom
call functions.
One button can be programmed to call another user in the column
or to call an indoor station in parallel. All indoor stations of the called
user will ring in the
fi
rst case. Only the speci
fi
cally programmed indoor
station will ring in the second case.
INTERCOM FUNCTION BETWEEN VARIOUS USERS
Go to the indoor station to be programmed as caller (indoor station
A).
Hold the button pressed for longer than 5 seconds. The yellow
LED will blink slowly to con
fi
rm that programming mode is
selected. In all cases, the device will quit programming mode and
save any changes after 10 minutes.
Hold the button to be programmed pressed for at least three
seconds until the con
fi
rmation tone is heard.
Go to the user who will be called by pressing the button (user B)
and press the door opener button. The apartment stations will be
beep to indicate that they have been programmed.
Alternatively, go to a calling station and press the calling button
of user B. The indoor station being programming (A) will beep to
indicate that it has been programmed. The indoor stations of user
B will ring when this occurs. Ignore this call.
Hold the button pressed for longer than 5 seconds to quit
programming mode.
Check the programmed function: release the handset A and press
the programmed button. Check that all indoor stations of user B
ring and check reply audio.
You will need to program indoor station B to call A to make the
opposite call possible
INTERCOM FUNCTION IN THE SAME APARTMENT
Go to the apartment station to be programmed as caller (indoor
station C1).
Hold the button pressed for longer than 5 seconds. The yellow
LED will blink slowly to con
fi
rm that programming mode is
selected. In all cases, the device will quit programming mode and
save any changes after 10 minutes.
Hold the button to be programmed pressed for at least three
seconds until the con
fi
rmation tone is heard.
Go to the apartment station that the button will call (apartment
station C2) and press the door opener button. The apartment
stations C1 and C2 will be beep to indicate that they have been
programmed.
Hold the button pressed for longer than 5 seconds to quit
programming mode.
Check the programmed function: release the handset C1 and
press the programmed button. Check that the apartment station
C2 rings and check audio.
You will need to program apartment station C2 to call C1 to make
the opposite call possible.
CALL TONE PROGRAMMING
In 2VOICE system each user can select the door phone call ring tone
and the
fl
oor call ring tone among the 5 available ones.
DOOR PHONE CALL RING TONE
The selected call ring tone is the same for all door phone calls.
—
—
—
—
—
—
—
—
—
—
—
—
—
However, the call ring tone source can be identi
fi
ed thanks to the call
ring tone timing:
Call source
Time
Ring total duration
Main call station 3 s ON
3 s
Secondary call
station
0,4 s ON 0,2 s OFF for
5 times
2,8 s
Intercom
0,5 s ON 0,5 s OFF for
3 times
2,5 s
Switchboard
0,1 s ON 0,05 s OFF for 3
times pause 0,2 s repeated
for 5 times
2,8 s
FLOOR CALL RINGTONE
Hold the button pressed for longer than 5 seconds. The yellow
LED will blink slowly to con
fi
rm that programming mode is
selected. In all cases, the device will quit programming mode and
save any changes after 10 minutes.
Press to change the ring tone
When the call ring tone has been selected, exit the programming
state
The call ring tone is programmed
RESET
To restore default parameters of the device after entering programming
mode, hold button pressed for longer than 5 seconds, press the
and
buttons together for longer than 3 seconds. The system will
emit two long beeps to con
fi
rm and exit the programming state.
•
•
•
•
2VOICE COMFORT DOOR PHONE Ref. 1183/5
OPTIONAL PROGRAMMING
2VOICE COMFORT DOOR PHONE
Ref. 1183/5
