10
−−−−
sec.4b
2 VOICE - Technical Manual
DOOR PHONE APARTMENT STATIONS
CODE 123
CODE 122
CODE 121
CODE 120
*
CODE 126
CODE 125
CODE 124
(*) Con
fi
guration not allowed, available for future development.
INT
: apartment station code
Set a number from 0 to 3 according to the following rules:
The indoor station code must be 0 if there is only one station in
the apartment.
Up to 4 apartment stations can be connected in parallel using the
same user code and different indoor station codes.
ON
1 2
INT=0
1 2
INT=1
1 2
INT=2
1 2
INT=3
The indoor station code is used to identify the single stations of the
same user. This means that intercom calls can be address to the single
user in the same apartment. All the users indoor stations will ring at
the same time in the event of intercom calls to different apartments,
door unit calls and
fl
oor calls.
The following considerations, should also be taken into account:
Extension 0 rings immediately when a call is received. Extensions
1, 2 and 3 will ring in sequence after each other.
LINE TERMINAL SETTINGS
A line terminal jumper (13) is
fi
tted in the door phone. Activate the
terminal for devices wired at the end of a line from which another
section does not start from the device terminals (end of line).
PERFORMANCE
CALL RECEPTION
The user’s apartment station will ring with the programmed tone when
a call is received according to the source:
From main door unit
From secondary door unit
Intercom call
Floor calls
From switchboard
The electric lock can be operated from the calling door unit also
without picking up the handset when a call is received.
Indoor station 0 will ring immediately if there are several stations in
the apartment. Extensions 1, 2 and 3 will ring in sequence after each
other.
ANSWERING A CALL
Press the button
to establish a conversation with the caller (the
button will start blinking as soon as it is pressed). Press the button
again to end the conversation and switch off the display.
ADJUSTING THE RINGER SPEAKER (MUTE)
Hold button pressed for longer than 5 seconds; the yellow LED
will blink slowly to indicate that programming mode is selected.
In any case, after 10 minutes the system exits the programming
state and saves the modi
fi
ed parameters.
Press the button
to change the ringer volume.
Quit programming mode when the required level is set
(HIGH,LOW,MUTE).
The multicolour LED 6 will blink to indicate mute status.
With the MUTE function on, all beeps will be deactivated.
•
•
•
•
•
•
•
•
•
•
•
SUPPLEMENTARY RINGER
The door phone is equipped with a pair of terminals (S+, S-) for
connecting a supplementary ringer or a relay. This ringer is controlled
when any call tone is generated.
FLOOR CALL
The door phone is equipped with a pair of terminals (CP) for connecting
the
fl
oor call button. If a
fl
oor call is received, the door phone will
play the ring tone selected by the user. Connect this button to one
extension only if there are multiple apartment stations in parallel. The
apartment stations will ring in sequence.
INTERCOM CALL FORWARDING
After having programmed a button for the intercom function, press the
audio button
and then press the programmed button.
The following cases can occur according to the calling indoor station
state:
Indoor station free: the calling indoor station will output a
con
fi
rmation tone (2 beeps) and the called indoor station will ring.
Communication is established when the called user picks up.
Line / System busy: the indoor station outputs a warning tone (4
beeps in rapid sequence). Hang up and try again later.
OPEN DOOR LED
The function is only active for the last called door phone on which
the door opening button was pressed and corresponding to the last
calling door unit; see the “LED indications” for more details.
Open door function is available only if a suitable sensor has
been connected to the door unit.
OPTIONAL PROGRAMMING
The following programming operations are needed after testing the
basic operation of the system, only if are required.
INTERCOM FUNCTION
Buttons , , can be programmed in 2Voice systems for intercom
call functions.
One button can be programmed to call another user in the column
or to call an indoor station in parallel. All indoor stations of the called
user will ring in the
fi
rst case. Only the speci
fi
cally programmed indoor
station will ring in the second case.
INTERCOM FUNCTION BETWEEN VARIOUS USERS
Go to the indoor station to be programmed as caller (indoor station
A).
Hold the button pressed for longer than 5 seconds. The yellow
LED will blink slowly to con
fi
rm that programming mode is
selected. In all cases, the device will quit programming mode and
save any changes after 10 minutes.
Hold the button to be programmed pressed for at least three
seconds until the con
fi
rmation tone is heard.
Go to the user who will be called by pressing the button (user B)
and press the door opener button. The apartment stations will be
beep to indicate that they have been programmed.
Alternatively, go to a calling station and press the calling button
of user B. The indoor station being programming (A) will beep to
indicate that it has been programmed. The indoor stations of user
B will ring when this occurs. Ignore this call.
Hold the button pressed for longer than 5 seconds to quit
programming mode.
Check the programmed function: release the handset A and press
the programmed button. Check that all indoor stations of user B
ring and check reply audio.
You will need to program indoor station B to call A to make the
opposite call possible.
•
•
—
—
—
—
—
—
—
2VOICE HAND-FREE DOOR PHONE Ref. 1183/7
PERFORMANCE - OPTIONAL PROGRAMMING
Ref. 1183/7
2VOICE COMFORT DOOR PHONE
