Ranchette Coop
(optional coop doubler)
Sides 36”
Sides 39 5/8”
You must FIRST read through the instructions for building the Round-Top Backyard Chicken Coop then NEXT
understand these variant instructions for the Ranchette Coop Extender Kit.
Look at pictures on the next page...they will help!
Ÿ
(R1)
One of your panels A6 will be
narrower, this is the Ranchette Part.
Ÿ
(R2)
You will not have any Run Backs
panel A2 and instead will have only one
panel that has a through door between
coops.
Ÿ
(R3)
Instead of the 2x4 back legs A8 you
will have 2- 2x6 legs to hook the two
coops together.
Ÿ
(R4)
You will not have the three side yard
fence boards C1,2,3 but rather 2 new
fence boards.
Door
Ranchette Mid-Panel
Concept:
A Ranchette is two Round-Top Coops connected back-to-back. If you will study the Round-Top
assembly instructions first, then read these instructions, you should be able to assemble the two coops together.
Never hesitate to call us at 877-741-2667 about anything you’re confused about or want to double check. You will need
to build the Ranchette in place as when it is done it will weigh the better part of 450 lbs and will require partial
disassembly to be moved.
These instruction reference other sections and Fig 13a.
Step 13.1 Run Sides & Fronts:
Attach side panels A1 of Coop 1 to front legs A7 and then stand them up holding
upright by installing header board A9. Repeat this process for Coop 2 so that the frames are sitting back-to-back as
illustrated in Fig 13a on next page.
(see steps 1-3)
Step 13.2 Attach Thru-Panel:
Attach Thru-panel R2 to back edges of side panels A1 of Coop 1 using 6 E1 Brown T25
Screws in pre-drilled holes so that top edges are flush and brackets at top of panel are facing Coop 2.
Step 13.3 Conjoin Coops:
Back Coop 1assembly up to the back of Coop 2 assembly and join them together using E4
4” Bolts & Washers & E5 T-Nuts through the R3 2x6 legs so that top edges of panels are all flush. Tighten E4 bolts to
seat E5 t-nuts then back out a little so they are slightly loose until after the next step.
Step 13.4 Attach Run Top Panels:
Using the illustration Fig 13a on the next page, position the 6 top panels onto the
coops with the A4 ramp panels on the outsides, the A5 storage side panels to the insides, and the R1 extender panel
on Coop 2 and the A6 extender panel on Coop 1. Square up edges and consistent with instructions in section 5 attach
tops of runs onto the doubled run assembly. Tighten E4 bolts in R3 & A7 legs at this point.
Step 13.5 Assemble and Place Roosts:
Consistent with steps 6-9, assemble the two roost / egg box assemblies and
attach to the outer ends of the run base assembly.
Step 13.6 Yard Boards:
Span the area between the roosts with the R4 yard boards using 1 E1 Brown T25 screw to
attach the ends of the boards to the egg boxes on one side and the sides of the roosts on the other. They are different
lengths.
Ranchette Assembly
13
© Urban Coop Company, all rights reserved.
1
R
R2
R3
R4
See Photos On Page 13b for Guidance
Содержание Backyard Chicken Coop
Страница 16: ...Shown with optional run extensions installed...
