![background image](http://html.mh-extra.com/html/upright/sl-26/sl-26_service-and-parts-manual_1061290013.webp)
2-6
Pre-Operation Safety Inspection
2.4 P
RE
-O
PERATION
S
AFETY
I
NSPECTION
NOTE:
Carefully read, understand and follow all safety rules, operating instructions, labels
and National Safety Instructions/Requirements. Perform the following steps each day
before use.
1. Open modules and inspect for damage, fluid leaks or missing parts.
Figure 3: Hydraulic Tank
6. Inspect
the machine thoroughly for cracked welds and structural damage, loose or missing
hardware, hydraulic leaks, damaged control cable, loose wire connections and wheel bolts.
2.5 S
YSTEM
F
UNCTION
I
NSPECTION
Refer to Section 2.3 for the locations of various controls and indicators.
W A R N I N G
!
!
STAND CLEAR
of the work platform while performing the following checks.
Before operating the work platform, survey the work area for surface hazards such as holes,
drop-offs, bumps and debris.
Check in
ALL
directions, including above the work platform, for obstructions and electrical
conductors.
Protect the control console cable from possible damage while performing checks.
1. Move the machine, if necessary, to an unobstructed area to allow for full elevation.
2. Twist Chassis Emergency Stop Switch to the ON position.
3. Twist Platform Emergency Stop Switch to the ON position.
4. Turn the Key Switch to the ON position.
5. Visually inspect the elevating assembly, lift cylinder, cables, and hoses for cracked welds and
structural damage, loose hardware, hydraulic leaks, loose wire connections, and erratic
operation. Check for missing or loose parts.
6. Push the Chassis ELEVATE and ENABLE buttons and fully elevate the platform.
7. Partially lower the platform by pushing Chassis DESCEND and ENABLE buttons, and check
for proper operation of the audible lowering alarm.
2. Check the level of the hydraulic fluid with
the platform fully lowered. The hydraulic
reservoir is located in the Control Module
Door. The fluid level must be between
the MIN and MAX lines. Add hydraulic
fluid if necessary.
3. Check that fluid level in the starter
battery is correct.
4. Check the level of the Diesel fuel with the
engine switched off. The fuel tank is
located in the Power Module. Add fuel as
required.
5. Check that all guardrails are in place and
all fasteners are properly tightened.
Содержание SL-26
