27
NOTE
: Ensure any existing remotes are present when
pairing to vehicle.
1. Turn ignition to
ON.
2. Turn
radio
OFF.
NOTE
: Ensure any existing remotes are present when
pairing to vehicle.
1. Turn the ignition to
RUN
or
ON
and the radio to
off. Do not crank the engine.
2. Press and hold the
DISP
button on the radio for at
OHDVW¿YHVHFRQGVXQWLOVHWWLQJVLVGLVSOD\HG
3. Press
the
SEEK
up or down arrows until
FOB PROG
appears on the display.
4. Press
the
PREV
or
NEXT
button to enter the sub
menu. The current selection will have an asterisk
next to it.
BEGIN
will be displayed.
5. Press
the
DISP
button to start pairing. When the
message
PUSH FOB
ÀDVKHVSUHVVDQGKROGWKH
LOCK
and
UNLOCK
EXWWRQVRQWKH¿UVWUHPRWH
at the same time for 15 seconds. A chime will be
heard to verify the remote is paired.
6. Repeat Step #5 for each additional remote up to
four remotes total. You do not need to press the
DISP
button again, just press down the
LOCK
and
UNLOCK
buttons on the next remote to be
learned to a maximum of four remotes per vehicle.
7. The mode you selected is now set. You can
either exit the
PAIRING MODE
by following the
instructions later in this section or pair the next
feature available on your vehicle.
8. You can exit the pairing mode by scrolling to exit
and pressing the
DISP
button.
9. Test all remotes (ignition must be
OFF
).
NOTE
: Ensure any existing remotes are present when
pairing to vehicle.
1. Close all doors.
2. Insert key into ignition.
3.
+ROGGRZQWKHSRZHU
UNLOCK
button on the
driver’s door panel, continue to hold down until
instructed to release in Step #9.
4. Perform Steps #5 through #8 in a fairly rapid
succession.
5. Turn the ignition to the
ON
position (as far as you
can go without starting the engine).
6. Turn the ignition to the
OFF
position.
7. Release the power
UNLOCK
button on the door
panel. The vehicle should respond by door locks
locking and unlocking automatically.
8.
+ROGGRZQWKH
LOCK
and
UNLOCK
buttons on
the remote until the doors lock and unlock. This
may take up to 30 seconds.
9. Repeat Step #1 now for each additional remote
(Including any existing remotes) if applicable. If
not, move to Step #10.
10. Turn the ignition to the
ON
position to exit the
pairing mode.
11. Test all remotes (ignition must be
OFF
).
4
5
3. Press Driver Information Center (DIC)
RESET
button.
4. Press
OPTIONS
button on DIC until display is
blank.
5. Press and hold
RESET
button for 3 seconds.
6. Press
OPTIONS
button until
FOB
TRAINING
is
displayed.
7. Press
RESET
button to begin pairing sequence.
8. Simultaneously press and hold
LOCK
and
UNLOCK
EXWWRQVRQ¿UVWUHPRWHIRUVHFRQGV
Message will appear when remote is paired.
9. Repeat this step for additional remotes.
10. Turn ignition
OFF
and remove keys
from ignition.
11. Test all remotes.
6
PAIRING
10.
+ROGGRZQWKH
LOCK
and
UNLOCK
buttons on
the remote simultaneously until the door locks and
unlocks. This step may take up to 30 seconds.
11. Repeat Step #10 now
for each additional remote
(including any existing remotes). If applicable. If
not move to Step #12.
12. Turn the ignition switch to the
ON
position in
order to exit.
13. Test remotes (ignition must be
OFF
).
