Universal Robots UR3/CB3 Скачать руководство пользователя страница 175

Страница: 175 / 256

14.6 Command: Fixed Waypoint

14.6

Command: Fixed Waypoint

A point on the robot path. Waypoints are the most central part of a robot program, telling the robot

arm where to be. A fixed position waypoint is taught by physically moving the robot arm to the

position.

Setting the waypoint

Press this button to enter the Move screen where you can specify the robot arm’s position for this

waypoint. If the waypoint is placed under a Move command in linear space (

moveL

moveP

there needs to be a valid feature selected at that Move command, in order for this button to be

pressable.

Waypoint names

Waypoints automatically get a unique name. The name can be changed by the user. By selecting the

link icon, waypoints are linked and share position information. Other waypoint information such

as blend radius, tool/joint speed and tool/joint acceleration is configured for individual waypoints

even though they may be linked.

Blending

Blending enables the robot to smoothly transition between two trajectories, without stopping at the

waypoint between them.

Version 3.10

Cop

ight

2009–2019

Univ

ersal

Robots

A/S

All

rights

reser

ed.

II-77

CB3

Содержание UR3/CB3


































































































































































































































Результаты поиска

Содержание UR3/CB3

Отзывы:

Похожие инструкции для UR3/CB3

Бренды по названию

Популярные бренды

Universal Robots UR3/CB3, Оригинальное руководство пользователя

Результаты поиска

Содержание UR3/CB3

Отзывы:

Похожие инструкции для UR3/CB3

Бренды по названию

Популярные бренды