Universal Robots UR3/CB3 Скачать руководство пользователя страница 146

Страница: 146 / 256

13.8 Installation

→

I/O Setup

• Analog standard general purpose and tool

• MODBUS

• General purpose registers (boolean, integer and float) The general purpose registers can be

accessed by a fieldbus (e.g., Profinet and EtherNet/IP).

13.8.1

I/O Signal Type

To limit the number of signals listed in the

Input

and

Output

sections, use the

View

drop-down

menu at the top of the screen to change the displayed content based on signal type.

13.8.2

Assigning User-defined Names

To easily remember what the signals do while working with the robot, users can associate names

to Input and Output signals.

1. Select the desired signal

2. Tap the text field in the lower part of the screen to set the name.

3. To reset the name to default, tap

Clear

A general purpose register must be given a user-defined name to make it available in the program

(i.e., for a

Wait

command or the conditional expression of an

command) The

Wait

and

com-

mands are described in

(14.11)

and

(14.20)

, respectively. Named general purpose registers

can be found in the

Input

Output

selector on the

Expression Editor

screen.

13.8.3

I/O Actions and I/O Tab Control

Input and Output Actions

: Physical and Fieldbus digital I/Os can be used to trigger actions or react

to the status of a program.

Available Input Actions:

• Start: starts or resumes the current program on a rising edge.

• Stop: Stops the current program on a rising edge.

• Pause: Pauses the current program on a rising edge.

• Freedrive: When the input is high, the robot is in freedrive ( similar to the freedrive but-

ton). The input is ignored if a program is running or other conditions disallow freedrive.

WARNING:

If the robot is stopped while using the Start input action, the robot

slowly moves to the first waypoint of the program before executing

that program. If the robot is paused while using the Start input ac-

tion, the robot slowly moves to the position from where it was paused

before resuming that program.

Available Output Actions:

• Low when not running: Output is low when the program state is “stopped” or “paused”.

• High when not running: Output is high when the program state is “stopped” or “paused”.

CB3

II-48

Version 3.10

Cop

ight

2009–2019

Univ

ersal

Robots

A/S

All

rights

reser

ed.

Содержание UR3/CB3


































































































































































































































Результаты поиска

Содержание UR3/CB3

Отзывы:

Universal Robots UR3/CB3, Оригинальное руководство пользователя, Страница: 146 / 256

Результаты поиска

Содержание UR3/CB3

Отзывы: