UniVer TC Скачать руководство пользователя страница 73

Страница: 73 / 80

Rev.B15

Pg. 73 di 80

Error codes in the CANopen diagnostics messages

The emergency message consists of 8 bytes with the data shown below:

Composition of the emergency message

Byte

Content

Emergency error

code

Error

(object

1001H)

Manufacturer’s specific error fields

Main

Diagnostics

0000-0000

Module No.2

Module No.1

Module No.4

Module No.3

Module No.6

Module No.5

Module No.8

Module No.7

MANUFACTURER’S SPECIFIC ERROR FIELDS

BITS OF THE MAIN DIAGNOSTICS (BYTE 3)

Bit

Name

Description

24V Main power loss

This bit at 1 indicates the lack of VA24 power supply (pin4 of the power

connector). In this condition the valve coils will not be powered even if the

command is active.

Module fail

This bit at 1 indicates that the module is faulty (replace the module).

Output fail

This bit at 1 indicates that one or more outputs are overloaded or in short circuit,

this applies both to the integrated manifold and to the output modules

(1)

High noise level

This bit at 1 indicates that a communication error has been detected on the

internal bus, caused by the high level of noise, due to bad wiring, lack of

grounding, or capacitive coupling of the connecting cables.

Input power loss

This bit at 1 indicates an overload or a short circuit in one or more connectors of

the input module.

Clamp Error

This bit at 1 indicates that one or more electric clamps are in error.

Moduli di Ingressi o

Moduli Uscite

This bit at 0 indicates that the content of the message refers to the input modules,

this bit at 1 indicates that the content of the message refers to the output modules

(3).

Module info Monitor

This bit at 1 indicates that an extended module diagnostics is available.

NIBBLES OF THE DIAGNOSTICS FOR INPUT AND OUTPUT MODULES (BYTE 4….7)

Binary

Description

0000

This value indicates that no error is present

0001

This value indicates the lack of power supply (VA24).

(2)

0010

This value indicates that one or more outputs are overloaded or in short circuit.

(2)

0011

This value indicates that a communication error has been detected on the internal bus, caused by a

high level of noise, due to bad wiring, lack of grounding, or capacitive coupling of the connection

cables.

0100

This value indicates a module failure.

0101

This value indicates an overload or short circuit in one or more connectors of the input modules.

0110

This value indicates that one or more electric clamps are in error (output FAULT active).

0111

This value indicates that one or more control outputs for the electric clamps are overloaded or in short

circuit.

1000 - 1111

Not yet assigned.

Содержание TC

















































































Результаты поиска

Содержание TC

Отзывы:

Похожие инструкции для TC

Бренды по названию

Популярные бренды

UniVer TC, Руководство пользователя

Результаты поиска

Содержание TC

Отзывы:

Похожие инструкции для TC

Бренды по названию

Популярные бренды