UniVer TC Скачать руководство пользователя страница 60

Страница: 60 / 80

Rev.B15

Pg. 60 di 80

Error codes of the EtherNet/IP diagnostics messaging

Use the following to get diagnostic information:

Service:

Get Attribute Single

Class:

01 (65 hex)

Instance:

Attribute:

The device will respond with 18 bytes; the first byte of them is the main diagnostics, while the further 17 bytes are the extended

diagnostics of the possible manageable modules.

BITS OF THE MAIN DIAGNOSTICS

Bit

Name

Description

24V Main power loss

This bit at 1 indicates the lack of the VA24 power supply (pin4 of the power

connector). In this condition the valve coils will not be powered even if the

command is active.

Module fail

This bit at 1 indicates that the module is faulty (replace the module).

Output fail

This bit at 1 indicates that one or more outputs are overloaded or in short circuit,

this applies both to the integrated manifold and to the output modules

(1)

High noise level

This bit at 1 indicates that a communication error has been detected on the

internal bus, caused by the high level of noise, due to bad wiring, lack of

grounding, pr capacitive coupling of the connecting cables.

Input power loss

This bit at 1indicates an overload or a short circuit in one or more connectors of

the input module.

Reserved

For future use.

Clamp Error

This bit at 1 indicates that one or more electric clamps are in error.

Module info Monitor

This bit at 1 indicates that an extended module diagnostics is available.

NIBBLE OF THE EXTENDED DIAGNOSTICS

Binary

Description

0000

This value indicates that no error is present.

0001

This value indicates the lack of power supply (VA24).

(2)

0010

This value indicates that one or more outputs are overloaded or in short circuit.

(2)

0011

This value indicates that a communication error has been detected on the internal bus, caused by a

high level of noise, due to bad wiring, lack of grounding, or capacitive coupling of the connection

cables.

0100

This value indicates a module failure.

0101

This value indicates an overload or short circuit in one or more connectors of the input modules.

0110

This value indicates that one or more electric clamps are in error (FAULT output active).

0111

This value indicates that one or more control outputs for the electric clamps are overloaded or in short

circuit.

1000 - 1111

Not yet assigned.

Byte

Main

Diag.

Valves

Slot

The high nibble is always equal to 0, except for the TCR32xD and TCR1616 modules (discontinued), where the low nibble identifies

the channel 0 (first connector A-C) and the high nibble identifies the channel 1 (second connector B-D).

If “Extended Module Diag” is disable, all the extended bytes (2-18) will be always equal to 0.

(1)

If the error is generated by the integrated manifold, it is possible to reset the error by turning off all the 24 outputs, wait for at least 7

seconds, and reactivate the needed outputs again.

In case of short circuit or overload, all the 24 outputs will be switched off.

(2)

Only on output modules.

Содержание TC

















































































Результаты поиска

Содержание TC

Отзывы:

UniVer TC, Руководство пользователя, Страница: 60 / 80

Результаты поиска

Содержание TC

Отзывы: