United States Stove American Harvest 6039I Скачать руководство пользователя страница 17

USSC

17

Your American Harvest Multifuel

 

Stove comes to you with the glass door installed in place, ready for use.  The glass

is surrounded on the edges with a gasket and seated in a glass channel.  It is held in place with two (2) clips.

REMOVAL OF BROKEN OR DAMAGED CERAMIC GLASS

Open the door and lift off of hinges.  If the door is tight, tap gently on the bottom of the door with your hand or rubber

hammer.  Lay door down on newspaper with glass clips facing you. Using a #2 Phillips screwdriver, loosen the screws and

take off the glass clips.  Remove the broken glass carefully and discard.

Reverse the above procedure for replacing new glass with new gasket.  Do not over tighten the screws.  Over tightening

can cause the glass to break.

WARNING

Do not operate unit with broken glass.

Do not substitute original factory glass.

You must use only factory authorized glass;

Do not slam door shut.

Do not strike glass.

Do not use abrasive cleaners.

Do not clean when glass is hot.

CLEANING THE GLASS

When the fire is first started, it will produce some smoke.  The soot might accumulate on the glass surface.  Before the glass

surface gets hot, open the door and wipe the glass surface off with a rag.  Do not touch the surface with your hands.  If after

constant use, the glass is dirty, you must clean the glass so that it will not become etched with the fly ash.  When the glass

has cooled off, take a damp ragand clean with Hearth Glass Cleaner available from your dealer.  Do not use a rag that

contains nylon because it will melt to the glass.

GLASS MAINTENANCE, REMOVAL AND REPLACEMENT

GLASS CLIPS

.

-

Содержание American Harvest 6039I

































Отзывы: