background image

Failure to follow operating instructions could result in death or serious injury. Please read and 

follow all instructions and guidelines before using products.

United Safety Incorporated and its distributors cannot be held responsible for improper or 

neglected maintenance, improper installation, or behavior that violates State, Federal an 

international laws and guidelines.

THIS IS AN ASSISTIVE AND INTERACTIVE DEVICE

-it cannot guarantee operator safety

Do not use product or machinery within 20’ from overhead power lines.

Do not operate any part of equipment directly above or below overhead power lines.

Contact with high voltage will result in serious injury or death. Observe general safety 

precautions when near high voltage power lines.

If product is damaged or collides with obstructions, remove unit immediately and return to the 

manufacturer for repair or replacement. Operating a damaged unit could lead to system failure.

This device is used to detect 50 and 60 Hz OVERHEAD power lines greater than 5000V volts

By using United Safety Incorporated products you understand and agree the dangers of 

operating machinery or equipment near overhead power lines and are familiar with associated 

risks.

In no event shall United Safety Incorporated or its distributors be liable for any direct, indirect, 

punitive, incidental, special consequential damages, to property or life, whatsoever arising out of 

or connected with the use or misuse of our products.

The Voltek NS does not measure or indicate distance. Power line proximity alarms measure 

relative strength of electromagnetic fields surrounding overhead power lines. Proximity alarms 

are interactive devices provided to assist you the operator in avoiding contact with power lines.

It is the expressed goal of United Safety Incorporated to provide you with the best safety 

products available, however it is imperative that the operator takes time to become fully 

educated in the potential hazards his or her work environment. We work to provide you with an 

extra measure of safety, however it is ultimately up to you to maintain a hazard-free job-site. 

Have a safe and productive day and let us know if we can do anything further to help you with 

your power line safety needs.

    

  Sincerely,

            United Safety Incorporated staff

For your safety:

Voltek NS User Guide

Page 1

Содержание Voltek NS














Отзывы: