Please read through these instructions carefully before using this product. They contain
all the important information you need to familiarise yourself with its functions. Retain
these instructions in case you have any questions during the life of the product and pass
them on to other users or subsequent owners.
this compressor has been designed mainly for inflating car and light commercial vehicle
tyres to the tyre pressures recommended by the vehicle manufacturer. It may also be used
for leisure products such as airbeds, air cushions and balls. To make the job easier in the
dark, the compressor has a built-in LeD work light. this LeD work light is not suitable for
lighting living areas.
1
transparent cover
2
LeD base
3
LeD lights
4
top cover
5
Decorative panel
6
Bottom cover
7
Compressor 28 mm
8
Support pads
9
Adapters
Vibration dampers
On/OFF buttons
Buttons
Pressure sensor
• Use only the accessories supplied with the product.
• 12 V cable with plug for the cigarette lighter
• Compressed rubber hose with screw lock valve
• 1 adapter each for balls and airbeds.
• Check that the vehicle‘s battery has enough charge to operate the compressor.
• Do not let the compressor operate for longer than 15 minutes at a time or there will be a
risk of overheating. then leave it to cool for at least 30 minutes.
• Do not leave the compressor unattended during the inflation process
• Do not use the compressor whilst travelling
• The compressor may become hot during operation
• Operate only with 12 V direct current
• Operate only in a dry environment
• Check the device for any damage every time before using it. Do not start up the device if
any damage or malfunction has been detected or if it has come into contact with water.
• Repairs may only be carried out by trained staff.
• Do not carry the device by its cable or pull on the cable to take the device out of the
socket. to take the cable out of the socket, grip the 12 V plug.
• Do not wind the cable around sharp corners or edges
• Do not operate the device with wet hands
• Before any routine cleaning or maintenance remove the device from the socket and first
allow it to cool down sufficiently.
• Children must not play with the device.
• Suitable ambient temperature for use: -15 to +55°C.
Intended use
Parts list
Accessories
Safety instructions
Original operating instructions
• Position the tyre so that the valve is as low as possible.
• Screw the rubber hose connector to the tyre valve. If the tyre is completely empty of air,
the vehicle should be raised a little with a jack so that there is no additional counter-
pressure acting on the empty tyre.
• Put the plug into the cigarette lighter (12 Volt). The compressor is now ready to operate.
• You can set the unit of measurement for pressure with the „SET“ button (BAR, PSI, KG/
CM³, KPA)
• Set the desired air pressure with the „+“ and „-“ buttons and start the compressor with
the „COMPRESSOR ON“ button. The device will switch off automatically when the set
pressure is reached. the inflation process may be interrupted by pressing the
„COMPRESSOR OFF“ button.
• After use, take the plug back out of the cigarette lighter.
• Select the appropriate adapter and connect the compressor to the item to be inflated.
• Put the plug in the cigarette lighter (12 Volt). The compressor is now ready to operate.
• You can set the unit of measurement for pressure with the „SET“ button (BAR, PSI, KG/
CM³, KPA)
• Set the desired air pressure with the „+“ and „-“ buttons and start the compressor with
the „COMPRESSOR ON“ button. The device will switch off automatically when the set
pressure is reached. the inflation process may be interrupted by pressing the
„COMPRESSOR OFF“ button. Avoid overinflating the item being inflated as this may
cause it to burst!
• After use, take the plug back out of the cigarette lighter.
• To switch the work light on and off please move the switch to the „LIGHT ON“ or
„LIGHT OFF“ position.
• Do not look directly into the work light.
• If the housing becomes dirty, wipe it with a damp cloth. Do not immerse the device in
water.
• Operating voltage:
12 V DC
• Maximum pressure:
10 bar
• Airflow rate:
22 litres/min
• Power:
0.096 – 0.120 kW, 0.214 kg
• Rotation speed:
16,000 rpm
• Noise level (when inflating): < 85 dB
At the end of its working life do not dispose of this product in the domestic refuse
but at the locations set up for the return of used electrical equipment.
1
2
3
4
5
6
7
8
9
10945_Bed_A5_131218.indd 4
27.01.14 13:39
Содержание YC2211B
Страница 12: ...10945_Bed_A5_131218 indd 12 27 01 14 13 40...