Unit USP-1070D, Инструкция по эксплуатации

Страница: 5 / 22

ENGLISH ENGLISH
8 9
FIXING AND TAKING OFF THE LID
Taking off the lid:
•
Put the appliance on a flat dry surface.
•
Turn the Lid around her axis a clockwise direction until it stops and lift up.
•
Unscrew the plug which is located under the handle of the Lid for a complete detaching of the
Lid (see pictures). Remove the Lid from the thread.
Fixing of the lid:
•
Set the detached Lid on carving of handle exactly in the form of holes
•
Put down the Lid and turn it counter-clockwise.
•
It is important that the Lid has been turned completely during cooking, because there is blocked
valve inside of the Lid which, in another case, will not allow to start the cooking process.
STEAMER FUNCTION
The appliance can be used as a Steamer. For this purpose use a special accessory that you have
bought with the appliance – the Steamer .
•
Add some water (1/5 scale) into the Inner Pot. Put the Steamer with kitchen-stuff into the Inner
Pot and close the Lid.
•
Turn the Relief Valve to “Герметично” position.
•
Power on the appliance with the Power Cord.
•
Choose the button “Пароварка”.
•
Cooking time is up to your preferences – control the cooking time according to your food or
menu. For this use the “Установка времени” button.
•
Press the “Отмена/Поддержание тепла” button if you would like to stop the cooking process.
COOLING SYSTEM
When the food is ready and the function “keeping warm” is switched , the pressure inside is high, the
protection devices don’t let open the Lid immediately. In order to speed up cooling down you can use
the cooling system to cool it and make the pressure down soon, especially when the food is fluid.
•
Unplug the device.
•
Turn regulator of reduce the pressure to the “vent of steam”.
•
The lid will be unlocked when internal temperature and pressure are reduced.
CLEANING
•
Remove the plug from the socket before cleaning wait until the appliance has normal tempera-
ture.
•
Take out the Inner Pot and clean it with a sponge or nonmetal soft brush, and then dry it with
towel.
•
Rub the Inner Surface of the appliance with a soft cloth.
•
Clean the outer coating of the appliance with a soft slightly wet towel. Never dip it in water for
cleaning or run water over it.
•
Take off the Water Collector and clean it with a wet towel. Put it back as shown in the picture:
•
Clean the Sealing Gasket, Relief Valve, and Floating Valve with soap water then dry them with a
towel. After cleaning put the parts together again.
Attention!
For your safety remember that when the appliance is on it must not contact with water
or other liquids especially the cord and the base of the appliance.
You must not dip the appliance into the water to avoid electric shock, fire or injuring.
Never wash the appliance in a dishwasher!
TROUBLESHOOTING
NO. A Problem
The Cause The Solution
1 Difficult to close the Lid The sealing gasket is not fixed
well Fix the sealing gasket well
2 Difficult to open the Lid The pressure inside is too high Let the steam out turning the
relief valve left or right
3 Steam leaks off the Lid There isn't a sealing gasket in
the Lid Put the sealing gasket into
the Lid (see “Appliance use”
paragraph)
The sealing gasket isn't clean Clean the Sealing Gasket
The sealing gasket is damaged
or deformed Change a broken or de-
formed Sealing Gasket to a
new one in a UNIT service
center
The Lid isn't fixed properly Fix the Lid properly
4 Indicating lights are not
on The appliance isn't powered on Check the power cord and
the plug
Some other problems Send the appliance to a UNIT
service center
5 E1 Open circuit of the sensor Send the appliance to a UNIT
service center
E2 Short circuit of the sensor
E3 Over-temperature
E4 Disable signal switch
E5 The lid is not covered well Cover the lid well