background image

Unimac Airless Paint Sprayer UM-SP-35

 

8

 

 

 

 

8

 

 

 

 

 

 
 

 

 
 

Before use

 

IMPORTANT! 

Test your airless sprayer for 

leaks before every use. 

 

 
 

   

WARNING! 

Never test spray on the actual 

work piece, always use an item that can be 
discarded. 

 

1.    Place the “prime / spray selector” in the Prime setting. 
2.    Close the “pressure valve” all the way by rotating it right (clockwise). 
3.    Place the inlet tube into a bucket of water. 
4.    Switch the motor on and push the “manual primer” valve repeatedly to help to draw liquid into the pump. 

In a few seconds, fluid will begin to flow up through the tube and flow out from the outlet valve. 

5.    Change the “prime / spray selector” to the Spray setting. 
6.    Close the pressure valve by rotating it left (anti-clockwise). 
7.    Using the pressure gauge, once the pressure has reached 22MPa, check if there is any leakage in the 

outlet hose. If there are no leaks, perform a test spray. 

 
 

 

Using your Airless Paint Sprayer

 

 

 

   

WARNING! 

Risk of injection; to reduce the risk 

of injection, never hold your hand, body, fingers 
or hand in a rag in front of the spray tip when 
cleaning or checking for a cleared tip. Always 
point the gun toward the ground or into a waste 
container when checking to see if the tip is 
cleared or when using a self-cleaning tip. 

   

WARNING! 

Always follow the "Pressure Relief 

Procedure" in this manual. 

   

WARNING! 

W hen you spray into the paint 

bucket, always use the lowest spray 
pressure. If the container is metal, maintain a 
firm metal to metal contact between the spray 
gun and container

.

 

   

Note! 

During your spraying if you need to stop 

for several minutes, loosen the pressure valve 
and  revolve prime  valve in  counter-clockwise, 
then switch the motor off. 

   

Avoid Spray Tip Blockages! 

There is an easy way to 

keep the outside of the tip clean from material build up: 

Every time you stop spraying, for even a minute, 
lock the gun and submerge it into a small bucket 
of thinner suitable for the material sprayed. 

Thinner will dissolve the build-up of paint on the 
outside of tip, tip guard and gun much more 
effectively if the paint doesn't have time to dry 
out completely. 

If the spray tip gets blocked, rotate it 180 
degrees and back again a few times, then move 
back into position to continue spraying

Содержание UM-SP-35


















Отзывы: