PARTE II: MANUAL DE INSTALACIÓN
24
ESQUEMA DE LAS CONEXIONES ELÉCTRICAS
Realizar las conexiones eléctricas en la bornera de alimentación siguiendo los esquemas adjuntos. El quemador es completo de todas
las conexiones y con enchufe para la sonda de modulación.
Rotación motor
Tras haber terminado la conexión eléctrica del quemador, controlar la rotación del motor eléctrico. El motor debe girar ( mirando el ven-
tilador de enfriamiento del motor) en sentido antihorario. Si está girando en sentido horario , invertir la alimentación trifasica y volver a
contolar la rotación del motor.
Quemador con el cuadro de mando separado
El cable de alimentacion del equipo debe tener una longitud correcta entre el panel de mando y el quemador.
Los cables deben tener una longitud correcta según las indicaciones.
Proteger los cables con una protección adecuada.
La seguridad eléctrica del equipo se obtiene cuando éste ha sido correctamente verificado por personal
profesionalmente calificado
ATENCION : Está prohibido utilizar las tuberías como conexión eléctrica para la tierra
La instalación debe ser efectuada respetando las normativas vigentes en materia y según las instrucciones del fabri-
cante, ésta debe ser efectuada por personal profesionalmente calificado .
Comprobar una eficaz conexión de tierra realizada como previsto por la normativa ..
No utilizar las tuberias y partes metálicas como conexión para la tierra
Conectar el cable de la tierra en la bornera MA , de longitud como fase y neutro .
No invertir fase y neutro
Para la conexión con la red eléctrica es necesario prever un interruptor omnipolar diferencial y magnetotérmico , tal
como previsto por la normativa de seguridad vigente .
Hacer controlar por parte de personal calificado que la instalación eléctrica sea adecuada a la potencia máxima absor-
bida por el equipo indicada en la placa , controlar especialmente que la sección de los cables de instalación sean del tipo
idóneo con la potencia absorbida por el equipo.
En caso de avería y/o malfuncionamiento del equipo, desactivarlo,absteniéndose de realizar cualquier intento de repara-
ción o de intervenir directamente .
Comprobar tensión y frecuencia prevista en la tarjeta del quemador
Comprobar la protección IP prevista en la placa del quemador
Antes de efectuar cualquier operación de limpieza o de mantenimiento ,desenchufar el equipo de la red de alimentación
interviniendo en el interruptor del equipo y/o en los correspondientes órganos de interceptación.
Otras
Utilizar cables correctos entre el quemador y la caldera
Para la alimentación general del equipo de la red eléctrica no está permitido el uso de adaptadores , tomas múltiples y/o
alargadores
ATENCION : controlar el calibrado del termico del motor ( + 5% +10% )
PELIGRO : la rotación no correcta del motor es un peligro para las personas
Содержание TLX92R
