Unigas K890A Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 133

Unigas K890A Скачать руководство пользователя страница 6

PART I: SPECIFICATIONS

6

Burner model identification

Burners are identified by burner type and model. Burner model identification is described as follows.

Technical Specifications

(*) NOTE ON THE WORKING SERVICE: the control box automatically stops after 24h of continuous working. The control box
immediately starts up, automatically.

Type

K750A

Model

MG. MD. SR.

*.

A. 1.

80.

EC.

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

1 BURNER TYPE

K750A- K890A - K990A

2 FUEL

MG - Natural gas - Light oil, LG - LPG Light oil

3 OPERATION (Available versions)

MD - Fully modulating - PR - Progressive

4 BLAST TUBE

SR = Standard blast tube + ABS polymer (silenced) air intake

5 DESTINATION COUNTRY

* - see data plate

6 BURNER VERSION

A - Standard, Y - Special

7 EQUIPMENT

1 = 2 gas gas proving system
8 = 2 gas gas proving maximum gas pressure switch

8 GAS CONNECTION

65 = DN65

80 = DN80

100 = DN100

125 = DN125

9 MICRO-PROCESSOR CONTROL

EC = micro-processor control, without inverter
ED = micro-processor control, with inverter

BURNER TYPE

K750A

K890A

K990A

K750A

K890A

K990A

Output

min. - max. kW

880 - 7500 1000 - 8900 1820 - 9900 880 - 7500 1000 - 8900 1820 - 9900

Fuel

MG - Natural gas - Light oil

LG - LPG Light oil

Category

(see next paragraph)

Gas rate- Natural gas

min.- max. (Stm

3

/h)

93 - 794

106 - 942

193 - 1048

-

-

-

Gas pressure

mbar

(see Note 2)

LPG rate

min.-max. kg/h

-

-

-

33 - 280

37 - 332

68 - 370

Light oil rate

min.-max. kg/h

74 - 632

84 - 750

153 - 835

74 - 632

84 - 750

153 - 835

Oil viscosity

cSt @ 40°C

2 - 7,4

Oil density

kg/m

3

840

Light oil train inlet pressure

bar max

2

Power supply

400V 3N ~ 50Hz

Total power consumption

kW

17,7

18,5

18,5

17,7

18,5

18,5

Electric motor

kW

15,0

15,0

15,0

15,0

15,0

15,0

Pump motor

kW

2,2

3,0

3,0

2,2

3,0

3,0

Protection

IP40

Operation

PR - Progressive

Gas train 65 / Gas connection

65 / DN65

-

65 / DN65

-

Gas train 80 Valves size / Gas connection

80 / DN80

Gas train 100 Valves size / Gas connection

100 / DN100

Gas train 125 / Gas connection

125 / DN125

Operating temperature

°C

-10 ÷ +50

Storage Temperature

°C

-20 ÷ +60

Working service (*)

Intermitent

Note1:

All gas flow rates are referred to Stm

3

/h (1.013 mbar absolute pressure, 15° C temperature) and are valid for G20 gas

(net calorific value H

i

= 34.02 MJ / Stm

3

);

Note2:

Maximum gas pressure = 500mbar (with

Siemens VGD or Dungs MultiBloc MBE)

Minimum gas pressure = see gas curves.

Note3:

Burners are suitable only for indoor operation with a maximum relative humidity of 80 %

«
...
4
5
6
7
8
...
»

Содержание K890A






































































































































Отзывы:

Нет отзывов