Unigas K890A Скачать руководство пользователя | Manualshive

Страница: 11 / 133

background image

PART I: SPECIFICATIONS

11

The values in the diagrams refer to

GPL

with a calorific value of 22300 kcal/Stm

3

(15°C, 1013 mbar) and a density of 2.14 kg/

Stm

3

. When the calorific value and the density change, the pressure values should be adjusted accordingly.

Where:

Natural gas pressure shown in diagram
Real gas pressure
Natural gas flow rate shown in diagram
Real gas flow rate
Natural gas density shown in diagram
Real gas density

Combustion head gas pressure curves

Combustion head gas pressure depends on gas flow and combustion chamber backpressure. When backpressure is subtracted, i

depends only on gas flow, provided combustion is properly adjusted, flue gases residual O2 percentage complies with “Recommended

combustion values” table and CO in the standard limits). During this stage, the combustion head, the gas butterfly valve and the

actuator are at the maximum opening. Refer to , showing the correct way to measure the gas pressure, considering the values o

pressure in combustion chamber, surveyed by means of the pressure gauge or taken from the boiler’s Technical specifications.

.

Measuring gas pressure in the combustion head

In order to measure the pressure in the combustion head, insert the pressure gauge probes: one into the combustion chamber’s pres-
sure outlet to get the pressure in the combustion chamber and the other one into the butterfly valve’s pressure outlet of the burner. On
the basis of the measured differential pressure, it is possible to get the maximum flow rate: in the pressure - rate curves (showed on the
next paragraph), it is easy to find out the burner’s output in Stm

3

/h (quoted on the x axis) from the pressure measured in the combustion

head (quoted on the y axis). The data obtained must be considered when adjusting the gas flow rate.

1

2

4

3

Note: the figure is indicative only.Key

1 Generator
2 Pressure outlet on the combustion chamber
3 Gas pressure outlet on the butterfly valve
4 Differential pressure gauge

Fig. 3

ATTENTION: THE BURNED GAS RATE MUST BE

READ AT THE GAS FLOW METER. WHEN IT IS NOT

POSSIBLE, THE USER CAN REFERS TO THE

PRESSURE-RATE CURVES AS GENERAL

INFORMATION ONLY.

«
...
9
10
11
12
13
...
»

Содержание K890A






































































































































Отзывы:

Нет отзывов

Похожие инструкции для K890A

Бренд: baltur Страницы: 30

Бренд: Ecoflam Страницы: 16

Бренд: Riello Burners Страницы: 52

SOUTHERN Series

Бренд: Warmington Страницы: 2

Бренд: Nu-Way Страницы: 14

Бренд: MUURIKKA Страницы: 16

Бренд: Unigas Страницы: 56

Бренд: Hargrove Страницы: 11

OPT-TT E Series

Бренд: Outdoor Plus Страницы: 16

Premium Burner 24 cm

Бренд: CACHFIRES Страницы: 52

Бренд: Cadac Страницы: 53

Бренд: Hanau Страницы: 6

Бренд: Paramount Fitness Страницы: 31

Бренд: Unigas Страницы: 132

Бренд: Enertech Страницы: 32

Бренд: ACV Страницы: 20

Бренд: Kettler Страницы: 24

FPB-19RPSBR14MT-N

Бренд: Firegear Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды