Unigas K890A страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 133

background image

PART II: INSTALLATION

22

ELECTRICAL CONNECTIONS

To execute the electrical connections, proceed as follows:

1

remove the cover from the electrical board, unscrewing the fixing screws;

2

execute the electrical connections to the supply terminal board as shown in the attached wiring diagrams;

3

check the direction of the fan motor (see next paragraph);

1

refit the panel cover.

Rotation of electric motor

Once the electrical connection of the burner is executed, remember to check the rotation of the electric motor. The motor should rotate
according to the “arrow” symbol on the body. In the event of wrong rotation, reverse the three-phase supply and check again the rota-
tion of the motor.

NOTE: the burners are supplied for three-phase 380/400/415/480 V supply, and in the case of three-phase 220/230/240 V sup-
ply it is necessary to modify the electrical connections into the terminal box of the electric motor and replace the overload
tripped relay.

Note on electrical supply

In the case where the power supply of the AUXILIARIES of the phase-phase burner (without a neutral), for the flame detection it is
necessary to connect the RC circuit Siemens between the terminal 2 (terminal X3-04-4 in case of LMV2x, LMV3x, LMV5x, LME7x) of
the base and the earth terminal, RC466890660. For LMV5 control box, please refer to the clabeling recommendations avaible on the
Siemens CD attached to the burner

WARNING! Respect the basic safety rules. make sure of the connection to the earthing system. do not reverse
the phase and neutral connections. fit a differential thermal magnet switch adequate for connection to the mains.
WARNING! before executing the electrical connections, pay attention to turn the plant’s switch to OFF and be
sure that the burner’s main switch is in 0 position (OFF) too. Read carefully the chapter “WARNINGS”, and the
“Electrical connections” section.
ATTENTION: Connecting electrical supply wires to the burner teminal block MA, be sure that the ground wire is
longer than phase and neutral ones.

WARNING: (only for double stage and progressive burners) The burner is provided with an electrical bridge
between terminals 6 and 7; when connecting the high/low flame thermostat, remove this bridge before connecting
the thermostat.

CAUTION: check the motor thermal cut-out adjustment

LMV2/3... - LMV5...

M

Key

C - Capacitor (22 nF , 250 V)
LME / LMV - Siemens control box
R - Resistor (1 M

Ω

)

M: Terminal 2 (LGB, LME), Terminal X3-04-4 ( LMV2x, LMV3x,
LMV5, LME7x)
RC466890660 - RC Siemens filter

«
...
20
21
22
23
24
...
»

Содержание K890A






































































































































Отзывы:

Нет отзывов

Похожие инструкции для K890A

Бренд: T&C Страницы: 12

Бренд: baltur Страницы: 50

Бренд: Cadac Страницы: 19

Бренд: Town & Country Fireplaces Страницы: 16

Firepit Burners

Бренд: Hargrove Страницы: 7

EcoSmart XL Series

Бренд: KAMINAKODA Страницы: 5

LNB 1000 Series

Бренд: Midco Страницы: 16

Бренд: Campingaz Страницы: 65

Бренд: Wayne Страницы: 32

Бренд: Dantherm Страницы: 12

Бренд: Dantherm Страницы: 38

Бренд: Weber Страницы: 44

Signature VCSSBI38

Бренд: Vermont Castings Страницы: 6

Бренд: Town & Country Fireplaces Страницы: 16

Бренд: Town & Country Fireplaces Страницы: 20

Бренд: BRAND-MAN Страницы: 9

Бренд: Riello Burners Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды