Uniden EXAI4580 - EXAI 4580 Cordless Phone Скачать руководство пользователя

Страница: 56 / 64

shown on the label.

If this equipment causes harm to the telephone network, the

telephone company will notify you in advance that temporary

discontinuance of service may be required. But if advance

notice isn't practical, the telephone company will notify the

customer as soon as possible. Also, you will be advised of

your right to file a complaint with the FCC if you believe it is

necessary. The telephone company may make changes in its

facilities, equipment, operations or procedures that could affect

the operation of the equipment. If this happens the telephone

company will provide advance notice in order for you to make

necessary modifications to maintain uninterrupted service.

Please follow instructions for repairing, if any (e.g. battery

replacement section); otherwise do not substitute or repair

any parts of the device except as specified in this manual.

Connection to party line service is subject to state tariffs.

Contact the state public utility commission, public service

commission or corporation commission for information. This

equipment is hearing aid compatible.

Should you experience trouble with this equipment, please

contact Uniden customer service at 800-297-023. If the

equipment is causing harm to the telephone network, the

telephone company may request that you disconnect the

equipment until the problem is resolved.

NOTICE: According to telephone company reports, AC electrical

surges, typically resulting from lightning strikes, are very

destructive to telephone equipment connected to AC power

sources. To minimize damage from these types of surges, a

surge arrestor is recommended.

Changes or modifications to this product not expressly

approved by Uniden, or operation of this product in any way

other than as detailed by the owner's manual, could void your

authority to operate this product.

This device complies with part 5 of the FCC rules. Operation

is subject to the following two conditions: () This device may

not cause harmful interference, and (2) This device must accept

any interference received, including interference that may cause

undesired operation. Privacy of communications may not be

ensured when using this phone.

To insure the safety of users, the FCC has established

criteria for the amount of radio frequency energy various

products may produce depending on their intended usage.

This product has been tested and found to comply with the

FCC's exposure criteria. For body worn operation, the FCC RF

exposure guidelines were also met when used with the Uniden

accessories supplied or designed for this product. Use of other

accessories may not ensure compliance with FCC RF exposure

guidelines and should be avoided.

Radio.Interference

Radio interference may occasionally cause buzzing and

humming in your cordless handset, or caused by external

sources such as TV, refrigerator, vacuum cleaner, fluorescent

lighting, or electrical storm. Your unit is NOT DEFECTIVE. If

these noises continue and are too distracting, please check

around your home to see what appliances may be causing

the problem. In addition, we recommend that the base not

be plugged into a circuit that also powers a major appliance

because of the potential for interference. Be certain that

the antenna on the unit is fully extended when needed. In

Содержание EXAI4580 - EXAI 4580 Cordless Phone

































































Результаты поиска

Содержание EXAI4580 - EXAI 4580 Cordless Phone

Отзывы:

Похожие инструкции для EXAI4580 - EXAI 4580 Cordless Phone

Бренды по названию

Популярные бренды

Uniden EXAI4580 - EXAI 4580 Cordless Phone, Руководство пользователя

Результаты поиска

Содержание EXAI4580 - EXAI 4580 Cordless Phone

Отзывы:

Похожие инструкции для EXAI4580 - EXAI 4580 Cordless Phone

Бренды по названию

Популярные бренды