manualshive.com logo in svg

unicraft 6706420, Руководство по эксплуатации, Страница: 8 / 38

Поделиться
Скачать
unicraft 6706420 Скачать руководство пользователя страница 8

8

PG-I SE Series | Version 1.04

Transport, packaging, storage

5.1 Packaging

All used packaging materials and packaging aids are re-
cyclable and should be taken to a materials recycling de-
pot to be disposed of.

The delivery packaging is made of cardboard, so please 
dispose carefully by having it chopped up and given to 
the recycling collection.

The film is made of polyethylene (PE) and the cushioned 
parts of polystyrene (PS). These materials should be 
taken to a collection point for recyclable materials or to 
the local waste disposal company.

5.2 Storage

Store the generator thoroughly cleaned in a dry, clean 
and frost-free environment. Generators must not be 
stacked on top of each other. Also no other objects may 
be placed on them.

If the generator is not used for more than 30 days, it is re-
commended to empty the fuel tank completely. For petrol 
motors, it is important to empty the carburetor pan: older 
petrol residues will damage the parts that come into con-
tact with them.

 

Short-term storage (less than 1 year) PG-I 42 SE 

Petrol in the fuel tank has a maximum lifetime of up to 1 
year if proper fuel stabilizers are added and stored in a 
cool, dry place. The petrol in the carburetor can be sedi-
ment and block the carburetor if it is not used or drained 
within 2 weeks.

Procedure 

1.  Ensure that all devices are disconnected from the ge-

nerator.

2.  Add a proper fuel stabilizer to the tank.

3.  Run the generator for 10 minutes to allow the treated 

fuel to pass through the fuel system and carburetor.

4.  While the generator is running, turn the fuel valve to 

the "OFF" position and keep the generator running 
until the engine shuts down due to fuel shortage. This 
normally takes a few minutes.

5.  Set the motor switch to "OFF".

6.  Allow the generator to cool down completely before 

proceeding.

7.  

Optional:

 To ensure that the fuel is drained comple-

tely from the carburetor, use the drain screw on the 
carburetor to drain excess fuel into a suitable contai-
ner.

8.  Remove the spark plug connector and spark plug and 

pour a tablespoon of oil into the cylinder.

9.  Slowly pull the cable to move the piston in the cylinder 

to distribute the oil and lubricate the cylinder.

10. Replace the spark plug and spark plug connector.

11. If the power generator contains a battery, disconnect 

and charge it as described in the instructions.

12. Clean the generator according to generator main-

tenance.

13. Store the generator in a cool, dry place away from di-

rect sunlight.

Long term storage (over 1 year) PG-I 42 SE

When storing for more than 1 year, the fuel tank and the 
carburetor must be completely empty.

Procedure

 

As for short-term storage, additionally applies: 

the fuel must be completely drained from the fuel tank 
and the carburetor. Drain the petrol into a suitable conta-
iner.

ATTENTION!

The generator should be started every seven days at 
the latest and run for approx. 30 minutes. If this is not 
possible and the generator is out of service for more 
than 30 days, appropriate measures should be taken 
to ensure proper storage.

ATTENTION!

It is important to prevent deposits in the fuel system 
(carburettor, fuel hose or tank) during storage. Alco-
hol-containing fuels (ethanol or methanol) can 
absorb moisture which leads to acid formation during 
storage. Acidic gases can damage the fuel system 
and should be drained for 30 days or more prior to 
storage. Never use engine or carburetor cleaner in 
the fuel tank as this could cause permanent damage.

ATTENTION!

Fire or explosion can cause severe burns or death. 
Fill or drain fuel only in well-ventilated outdoor 
spaces. Do not pump fuel directly into the generator. 
Use an approved container to transport fuel to the 
generator. Never use a fuel tank, hose, cylinder or 
other fuel-related object that is damaged or appears 
to be damaged. Do not overfill the fuel tank. Keep 
fuel away from sparks, open fire, ignitions, heat and 
other ignition sources. Do not light or smoke cigaret-
tes.

ATTENTION!

Petrol is highly flammable and explosive under cer-
tain conditions. Do not smoke or produce sparks in 
the immediate environs.

Содержание 6706420







































Отзывы:

Нет отзывов