unicraft 6706420 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 38

unicraft 6706420 Скачать руководство пользователя страница 20

20

PG-I SE Series | Version 1.04

Start generator PG-I 80 SE

Fig. 21: Electrical start

Manual start

Use the pull starter if the battery voltage is too low to
drive the starter.

- Set the engine switch to ON.

Abb. 22: Manual Start

-Pull lightly on the starter handle until you feel resistance.

Then pull quickly in the direction of the arrow as shown
in Fig. 23.

Fig. 23: Manual start using the pull starter

- Let the motor run for 15 to 30 seconds and then turn the
multiswitch to the RUN position.

Fig. 24: RUN Position

- Connect the consumer.

11.1Switching off the generator

Step 1: Switch off and disconnect all electrical consu-

mers. Never start or stop the generator when
electrical appliances are connected or swit-
ched on.

Step 2: Let the generator idle for a few minutes to stabi-

lize the internal temperatures of the engine and
generator.

Step 3: Set the motor switch to "OFF.

Fig. 25: Motor switch OFF position

Step 4: Turn the multiswitch to "OFF.

Fig. 26: Multiswitch OFF position

NOTE!

Do not let the handle snap back after starting. Let the
handle slide back to its original position carefully.

«
...
18
19
20
21
22
...
»

Содержание 6706420







































Отзывы:

Нет отзывов