manualshive.com logo in svg

unicraft 6706420, Руководство по эксплуатации, Страница: 21 / 38

Поделиться
Скачать
unicraft 6706420 Скачать руководство пользователя страница 21

Start generator PG-I 80 SE

PG-I SE Series | Version 1.04

21

How to stop the engine in an emergency situation:

Set the motor switch to OFF.

11.2Connection of consumers 

Before connecting a device or power cord to the power 
generator:

- Make sure that it is in good condition. Faulty equipment 
or power cords can cause electric shock.

- If an appliance stops working normally, becomes slug-
gish or stops suddenly, turn it off immediately. Dis-
connect the appliance from the power supply and deter-
mine if the problem is with the appliance or if the rated 
load of the power generator has been exceeded.

Most appliance motors require more than their rated po-
wer to start. Make sure that the electrical power of the 
tool or device does not exceed the maximum power of 
the generator. In any case, the total power consumption 
of all connected devices must be considered. 

11.3Parallel connection between 2 po-

wer generators (optional)

Before connecting a consumer to one of the power gene-
rators, make sure that the consumer is in good condition 
and that its electrical rating does not exceed that of the 
socket.

Most motorized devices require more than their electrical 
power to start. When an electric motor is started, the 
overload indicator (red) may light up. This is normal if the 
OVERLOAD indicator (red) goes out within 5 seconds. If 
the OVERLOAD indicator (red) remains lit, contact your 
generator dealer.

During parallel operation, the Eco switch on both genera-
tors should be in the same position. Connect the parallel 
power cable between two generators.

11.4Feeding into the power grid

Connections to the electrical system of a building.

The connections for the emergency power supply of the 
electrical system of a building must be made by a quali-
fied electrician. It must be possible to disconnect the po-
wer generator from the power supply system. It must 
comply with all applicable laws and electrical regulations. 
In some areas, the registration of power generators with 
local utility companies is required by law. Check the local 
regulations for proper registration and use.

DANGER!

Maintain a free space of at least 1 meter on all sides 
of the product during operation and storage, even 
overhead. Allow to cool for at least 30 minutes before 
storage. Heat generated by exhaust and fumes may 
be sufficient to cause severe burns and/or ignite 
combustible objects.

CAUTION!

The ground cable must be installed and functional 
(where necessary). 

CAUTION!

Make sure that the parallel connection cables have 
been inserted correctly into the parallel connection 
socket. If the cables have not been connected cor-
rectly, starting them may damage the generator. 

DANGER!

Only two identical power generators can be 
connected in parallel. The parallel connection of 
more than two generators is not allowed.  
The parallel connection may only be made with the 
special cables supplied with the power generator. 
When using the parallel connection between the 
power generators, make sure that the plugs are 
always fully inserted into the sockets. Insert the plugs 
into the sockets of the parallel connection in the cor-
rect way. 
Do not pull out the connecting cables during parallel 
operation. 
The parallel connection cables must be connected 
before commissioning and may only be pulled out 
after the power generators have been switched off. If 
one of the two power generators is switched off 
during parallel operation, no power is supplied at the 
output. 
If only one power generator is used, make sure that 
the cables of the parallel connection have been pul-
led out. 
If the two power generators operate independently, 
do not use a parallel connection. 

DANGER!

Improper connections to the electrical system of a 
building can lead electricity from the power genera-
tor back into the supply lines. Such recycling can kill 
utility workers or others who come into contact with 
the lines during a power outage, and the generator 
can explode, burn or cause a fire when power is 
restored. Consult the utility company or a qualified 
electrician before making power connections.

Содержание 6706420







































Отзывы:

Нет отзывов