background image

9.

Removal of lip seal

Installation of lip seal

I. Removal of the felt

 

Procedure: 

Removal of the felt on the shaft by hooking 

with the slender bar.

II. Removal of snap ring

Tools required:

  

• 

Snap ring pliers 

(hole)

Procedure: 

Remove the snap ring slowly with pliers as 

shown in the figure.

III. Removal of lip seal

Tools required:

  

• 

Lipseal remover

Procedure: 

Insert the lip seal into the recess as shown in 

the figure, turn around lightly and pull out.

IV. Inspection of lip seal

1. Felt seal

 - should be dry.

2. Snap ring

 - must be in one piece and not deformed.

3. Lip seal.

I. Setting the guide sleeve

 

Tools required:

  

• 

Stand 

 Guide sleeve 

Procedure: 

Place compressor on the stand. Lubricate 

outside of the guide sleeve and insert into the shaft of the 
compressor.

Caution - the sleeve must be clean and unmarked.

II. Installation of lip seal

Tools required:

  

• 

Guide sleeve 

 Lipseal installer

Procedure: 

Slice the lipseal over the guide sleeve. Place the 

remover on the lip seal correctly and press the lipseal with 
the remover until it stops. Then remove the guide sleeve.

Bar

Remover

Felt

Snap ring

Lipseal

Guide sleeve

Lipseal

Содержание UX330

















Отзывы: