UNI-T UT233 Скачать руководство пользователя страница 11

Страница: 11 / 49

Model UT233: OPERATING MANUAL

Button

SAVE

MAX/

Operation Performed

MENU

Phase sequence

Press to start recording of maximum value,
it valid at voltage, current, active power,
apparent power and reactive power
ranges only.
Press once at LOAD mode, MR icon
shown, the Meter displays the next
stored reading

LOAD

Press once to enter LOAD mode, MR
appears and the Meter beeps.

Press again to exit LOAD mode, MR
disappears and the Meter beeps.
Press and hold

LOAD

for 1 second to

display the stored data quickly.

SELECT

At Active power (main display) + AC Voltage
(left secondary display) + AC Current (right
secondary display) mode, press

SELECT

button to step through first phase, second
phase, third phase and sum of watts.

Operation Performed

SELECT

At other mode except phase sequence,
press

SELECT

to step through first

phase, second phase and the third
phase.

Press once to store single reading,
Press and hold for over 1 second to
continuous store reading. Press

SAVE

again to exit. The maximum number
of data store is 99, when it achieves
99, the Meter shows FULL. Press

CLEAR

to clear the stored reading in

order to store next reading.

C L E A R

At active energy range, press to reset
time the zero, then restart the timing.
At all other ranges, press to clear stored
readings.

MIN /

Press to start recording of minimum
value, it valid at voltage, current, active
power, apparent power and reactive
power ranges only.

Содержание UT233


















































Результаты поиска

Содержание UT233

Отзывы:

Похожие инструкции для UT233

Бренды по названию

Популярные бренды

UNI-T UT233, Руководство по эксплуатации

Результаты поиска

Содержание UT233

Отзывы:

Похожие инструкции для UT233

Бренды по названию

Популярные бренды