Uni-ram URS500 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 25

background image

21

MANUAL - SOLVENT RECYCLERS - URS500, 600, 500EP2, 600EP2

Revision 2019-07

ERROR

CODE

Flashing LED

Lights

Description

Action Required

READY

(L)

READY

(H)

32

3 TIMES

2 TIMES

Micro Controller has been reset
due to power interruption or drop
in voltage during the recycling
operation.

Press “OFF” and then “ON” but-
tons to resume operation. Discon-
nect power at the source for about
30 seconds. Usually nothing is
wrong with the unit.

33

3 TIMES

3 TIMES

a) Recycling did not ﬁ nish in 6
hours due to power interruption or
excessive debris in Liner Bag

a) Clean Distillation Tank following
Operating Procedure 7, replace
Liner Bag, following Operating
Procedure 9,

b) Temperature Set Point is too
low for the solvent.

b) increase Temperature Set Point
following Operating Procedure 4
and recycle with virgin solvent

c) Boiling point of solvent is
above maximim set point.

c) Solvent cannot be recycled.

«
...
19
20
21
22
23
...
»

Содержание URS500 Series


























Отзывы:

Нет отзывов

Похожие инструкции для URS500 Series

Бренд: Landoll Страницы: 52

Бренд: Gason Страницы: 110

Бренд: Raith Страницы: 26

Бренд: Kane Страницы: 16

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: Daktronics Страницы: 30

Бренд: DAKOTA ULTRASONICS Страницы: 28

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

Бренд: OceanSat Страницы: 85

Бренд: Haag-Streit Страницы: 16

Бренд: NEILPRYDE Страницы: 55

Бренд: HANYOUNGNUX Страницы: 4

Бренд: Park House Healthcare Страницы: 6

Бренд: J&M Страницы: 33

AquaPure Ei Series

Бренд: Jandy Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды