UNAOHM DG-OHM Compact Скачать руководство пользователя

Страница: 9 / 36

DG-OHM

UNAOHM Srl Rev. 4.0

4 KEYBOARD

Button Single Press

Press and Hold

Spectrum

Modifies spectrum expansion

Activates frequency entering

Changes frequency increase digit

Digital measurements

OFDM / QAM selection (for FULL HD only)

Stored programme recall

Programme table

NIT download and picture viewing

TV menu

3 in 1: spectrum, digital measurements
and NIT

On the digital screen, stores instant
measurements and, in spectrum, opens
Data Logger

Activates modifications of terrestrial CH
and satellite TP

Switches terrestrial / satellite band

Sends DiSEqC command

DiSEqC menu

Activates side menu

Activates main menu

LNB On/Off and voltage regulation

Menu with LNB settings

In spectrum, increases attenuation and
in menus, moves the cursor

---------

In spectrum, decreases frequency and
channel and, in menus, modifies options

Fast decrease

Confirms selection

Adjustments menu

In spectrum, increases frequency and
channel and, in menus, modifies options

Fast increase

In spectrum, decreases attenuation and
in menus, moves the cursor

Automatic attenuator

---------

Instrument On/Off

4.1 STATUS BAR

The status bar at the bottom of the screen superimposes all main information for constant
viewing. You can make it transparent in TV pictures mode by simply pressing (single click) the

button and modifying the BLACK or TRANSPARENT choice in the box.

In addition, the status bar will change colour depending on the environment to be measured:

1. Red:

power measurements for digital terrestrial.

2. Green:

level measurement (CHBW: 1 MHz) for terrestrial band analogue signals.

3. Light blue:

level measurements for satellite band analogue signals.

4. Blue:

power measurements for digital satellite.

Frequency

Channel/tpsat programmes

Power/level

Vcc (voltage)

ATT

698.00

86.6

Содержание DG-OHM Compact





































Результаты поиска

Содержание DG-OHM Compact

Отзывы:

Похожие инструкции для DG-OHM Compact

Бренды по названию

Популярные бренды

UNAOHM DG-OHM Compact, Руководство пользователя

Результаты поиска

Содержание DG-OHM Compact

Отзывы:

Похожие инструкции для DG-OHM Compact

Бренды по названию

Популярные бренды