UNAOHM DG-OHM Compact Скачать руководство пользователя | Manualshive

Страница: 35 / 36

background image

DG-OHM

UNAOHM Srl Rev. 4.0

34

Attention! ALWAYS USE THE SAME USB PORT.
Repeat the drivers procedure whenever using a different port.
If you do not know which COM(xx) port to use, you can verify the type on your computer, from
the HARDWARE - DEVICE MANAGER - COM and LPT PORTS control panel.

2. DG-OHM FIRMWARE UPDATE



Switch off the instrument and connect it to the home network.



Download the *.upg file for the instrument FROM WEBISTE

www.unaohm.it

, download

section.



Connect the instrument (switched off) to the PC via USB cable.



Start up the uploader programme.



Select the COM port from the uploader programme.



Switch on the instrument and, after a few seconds, you will see

the message

INSTRUMENTS ON LINE.



Then, the preliminary version of the firmware

BOOTLOADER VER

.x.y will be detected.



Select the *.upg downloaded from the website

www.unaohm.it

.



Select .

Start

. on the uploader programme.



To verify proper updating, wait for the message:



Verification Successful

:

update completed correctly.



Verification failed:

update not completed correctly.

•

Click on

Restart

in the uploader programme to re-start the instrument.



Close the uploader programme and disconnect the instrument.

If you encounter problems during the upgrade, repeat the operation. If problems persist,
contact UNAOHM technical support.

«
...
33
34
35
36
»

Содержание DG-OHM Compact





































Отзывы:

Нет отзывов

Похожие инструкции для DG-OHM Compact

Бренд: Felix Instruments Страницы: 102

LaserRange-Master T4 Pro

Бренд: LaserLiner Страницы: 68

DC1500 CHLORINE

Бренд: LaMotte Страницы: 60

Бренд: NARDA Страницы: 64

Бренд: DODODUCK Страницы: 2

Бренд: Spasciani Страницы: 26

Бренд: Ramsey Electronics Страницы: 40

Бренд: Michell Instruments Страницы: 28

Бренд: 3nh Страницы: 39

Бренд: Polimaster Страницы: 24

Бренд: Hach Страницы: 2

Бренд: AXE Страницы: 5

VACTEST GCD 200

Бренд: BUSCH Страницы: 12

TRAVELER 3D ARM

Бренд: GRAVITY Страницы: 2

Бренд: SAND Страницы: 15

Бренд: SNV Engineering Страницы: 43

Proline Promag W 400

Бренд: Endress+Hauser Страницы: 64

Бренд: SPEEDMATE Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды