UltraLift MERCURY SLIM Скачать руководство пользователя страница 13

Страница: 13 / 15

WIRING AND OPERATION

MERCURY SLIM

WIRING AND OPERATION

Motor Controller Speciation

•

Input: 220 VAC / 50 Hz ± 10%

•

Output: 220 VAC

•

Power: Max. 500 W

•

Maximum motor running time: 5 minutes

•

Both RF and IR receiver

•

Dry contact closures.

•

External IR Lead & Built in IR Eye.

•

12 Volt trigger input for projectors

•

Programmable

Pairing Remote Control to Receiver:

Aim the Remote-control unit towards the receiver IR eye (IR1) or to the external IR eye while

programming.
Push button switch (SW4), (LED1 blinks) then press the UP button of the remote-control unit.

Unpairing Remote Control from Receiver:

Press SW4 (LED1 blinks) then press the DOWN button of the remote-control unit.

Unpairing All Remote Controls from Receiver:

Press and hold SW4 for about 4 seconds until LED1 blinks at faster rate, then release the Button. Then

press SW4 again.

Reversing The Up-Down Button Direction:

Press SW4 (LED1 blinks) then press the STOP button of the remote-control unit.

HEX Codes

0x0B

Down 0x43
Stop 0x23

Mo tor Controller Box (Side View )

Remote Control

Содержание MERCURY SLIM
















Результаты поиска

Содержание MERCURY SLIM

Отзывы:

Похожие инструкции для MERCURY SLIM

Бренды по названию

Популярные бренды

UltraLift MERCURY SLIM, Руководство по эксплуатации продукта

Результаты поиска

Содержание MERCURY SLIM

Отзывы:

Похожие инструкции для MERCURY SLIM

Бренды по названию

Популярные бренды