Ultra Start 35 SERIES Скачать руководство пользователя | Manualshive

Страница: 1 / 24

background image

INSTALL GUIDE

www.ultrastarters.com

Technical Support: 866-698-5872 ext 0

[email protected]

Covers All 35xx Series Advanced

2-Way Remote Starters

The system must be placed into Service Mode before any service work is started on the
vehicle. It is the sole responsibility of the vehicle owner to ensure that this is done. The
manufacturer accepts no liability or responsibility for accidental starting of the vehicle.
CARBON MONOXIDE - Never Start in an Enclosed Building (Garage, Carport etc...)
- The Hood Pin Safety Switch Must Always be Installed!

Warning!!

CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH!

It is the sole responsibility of the user to place the system in Service Mode
when parking in an enclosed area

ex: garage

, partially enclosed area

ex: carport,

or when the vehicle is being serviced.

1
2
3
...
»

Содержание 35 SERIES

























Отзывы:

Нет отзывов

Похожие инструкции для 35 SERIES

Бренд: Valor Страницы: 20

Бренд: IDK Страницы: 96

Бренд: Scanreco Страницы: 10

Бренд: LCT Страницы: 5

Бренд: Z-Wave Страницы: 9

Бренд: TriMark Страницы: 12

Бренд: REMdevice Страницы: 14

Бренд: Faber Страницы: 12

Бренд: Chauvet Страницы: 8

Бренд: SystemAir Страницы: 73

EVO-ONE RFK1004

Бренд: Fortin Страницы: 6

Бренд: Fortin Страницы: 8

Бренд: Fortin Electronic Systems Страницы: 32

Бренд: Clifford Страницы: 7

Бренд: Clifford Страницы: 17

Бренд: Zehnder Rittling Страницы: 88

Бренд: Arrma Страницы: 6

Бренд: Extron electronics Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды