Ultra Start 35 SERIES Скачать руководство пользователя

Страница: 18 / 24

Setting 1 Special Door Lock/Unlock Operations

(Factory Alarm Rearm)

1) Type 1 1 Flash/Honk Unlock before start. Lock pulse after start and shutdown.
2) Type 2 2 Flashes/Honks Lock pulse ONLY after remote start shutdown.

*3) Type 3 3 Flashes/Honks Default Lock/ Unlock Pulses.

Press & Release the Program Button 1 Time

(Setting 1) Confirmed with 1 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/horn (optional) honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 2 Gas/Diesel Mode

1) (+) Input 1 Flash/Honk (+) Glow Plug input. Waits maximum 30 seconds
.2) Time Delay 2 Flashes/Honks Waits for approximately 15 seconds.

*3) Gas/ (-) Input 3 Flashes/Honks Waits 2 seconds if no diesel input is detected.

Press & Release the Program Button 2 Times (Setting 2)

Confirmed with 2 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/horn (optional) honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 3 Rearm Output (Auxiliary Connector Pin 1)

1) Type 1 1 Flash/Honk Pulse after start and with lock.
2) Type 2 2 Flashes/Honks Pulse after start only.

*3) Factory Re-arm 3 Flashes/Honks Pulse with lock and after starter shutdown.

Press & Release the Program Button

3 Times (Setting 3) Confirmed with 3 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/horn (optional) honks, then release.

Press & Release the Program Button

to proceed to the next step.

Setting 4 Run Time

1) 4 Minutes 1 Flash/Honk Runs for approx. 4 minutes when activated.
2) 45 Minutes 2 Flashes/Honks Runs for approx. 45 minutes when activated.

*3) 15 Minutes 3 Flashes/Honks Runs for approx. 15 minutes when activated.

Press & Release the Program

Button 4 Times (Setting 4) Confirmed with 4 LED flashes.

Press & Hold the Program Button

until the appropriate # of park lights/horn (optional) honks, then release.

Press & Release the Program Button

to proceed to the next step.

INSTALL MANUAL

REMOTE VEHICLE STARTER

PAGE 18

Press and

Release the

button for

Menu 3

Menu 3- Starter Settings

Ignition 3x

On/Off

On/Off On

Press and

Release the

Program

Button

Press and Release

the Program Button

# of Times for

Setting Chosen

Press and Hold

the Program Button

to Change Option

Содержание 35 SERIES

























Результаты поиска

Содержание 35 SERIES

Отзывы:

Похожие инструкции для 35 SERIES

Бренды по названию

Популярные бренды

Ultra Start 35 SERIES, Инструкция по установке

Результаты поиска

Содержание 35 SERIES

Отзывы:

Похожие инструкции для 35 SERIES

Бренды по названию

Популярные бренды