Ultra Start 32 SERIES Скачать руководство пользователя

Страница: 21 / 24

Page 21

2WAY REMOTE VEHICLE STARTER

INSTALLATION MANUAL

Transmitter Programming

Step 1

- Within 3 seconds turn the ignition

ON-OFF-ON-OFF-ON

Leaving Key ON

Step 2

Press and hold the Program Button

- The park lights will turn ON and the siren will chirp once.*

Continue to hold the Program Button

, the park lights will turn off and the siren will chirp 5 times quickly.

Step 3

- While holding the Program Button, press the

LOCK

button on each of the remote’s to be programmed.

If remote’s are being programmed for 2nd Car Operation press the

button on each of the

2nd car

remote’s to be programmed.

Note:

The park lights will flash once and the siren will chirp once each time a new code is learned.

Note

Transmitter programming must done quickly. Do not pause more than one second between each transmitter.

All the transmitters

to be used must be programmed at the same time.

All transmitters not programmed

at this time will be erased from memory for security. The system holds a maximum of 4 transmitter
codes including 2nd car remote codes.

*If the Park Lights do not turn ON, turn ignition OFF, wait 5 seconds and repeat steps 1&2

When the Battery Icon on the remote indicates that the battery is low the
battery should be changed promptly. Replace with quality 1.5volt “AAA”
battery.

Battery Replacement

Ignition 3x
On/Off
On/Off On

Press and
HOLD the
Program
Button

Press and
Release
Button # 1

1 2 3

tter

Slide

Lift

Slide

Positive

Negative

Содержание 32 SERIES

























Результаты поиска

Содержание 32 SERIES

Отзывы:

Похожие инструкции для 32 SERIES

Бренды по названию

Популярные бренды

Ultra Start 32 SERIES, Инструкция по установке

Результаты поиска

Содержание 32 SERIES

Отзывы:

Похожие инструкции для 32 SERIES

Бренды по названию

Популярные бренды